BMW E46 starting problem after cloning EWS3

[daten]

Hi everyone
I have problem with BMW E46 from cloning EWS and now the car turns the engine but does not start. Unfortunately I do not have the car here and the workshop that I commissioned this job does not have adequate diagnostic equipment to synchronize DDE / EWS. Before sending the EWS I checked the two keys in the bank with an ews test rig and everything seemed correct.
Could someone tell me if it is possible to sync DDE / EWS without having the car. I attach the original ews reading in case someone can review the file
EWS reference: 6135 6 905 669 HW03 SW8


Thanks

[kiszka]

Hi everyone
I have problem with BMW E46 from cloning EWS and now the car turns the engine but does not start. Unfortunately I do not have the car here and the workshop that I commissioned this job does not have adequate diagnostic equipment to synchronize DDE / EWS. Before sending the EWS I checked the two keys in the bank with an ews test rig and everything seemed correct.
Could someone tell me if it is possible to sync DDE / EWS without having the car. I attach the original ews reading in case someone can review the file
EWS reference: 6135 6 905 669 HW03 SW8


Thanks

you have the eeprom reading of the old EWS

[daten]

You mean reading EWS donor (new)?
If I have, I attach the file

[pioneer427]

Hi everyone
I have problem with BMW E46 from cloning EWS and now the car turns the engine but does not start. Unfortunately I do not have the car here and the workshop that I commissioned this job does not have adequate diagnostic equipment to synchronize DDE / EWS. Before sending the EWS I checked the two keys in the bank with an ews test rig and everything seemed correct.
Could someone tell me if it is possible to sync DDE / EWS without having the car. I attach the original ews reading in case someone can review the file
EWS reference: 6135 6 905 669 HW03 SW8


Thanks
Try this
Ign ON
WAIT
ign OFF
WAIT
Start engine
Pass in pm

[pioneer427]

Your pm is full

[lupu_sandu]

I'm thinking that you don't reset rolling codes from keys.
Test this one, no pass.

[pioneer427]

The engine crank , it means the keys are ok

[daten]

Your pm is full

Please can you send me the password
Thank you

[lupu_sandu]

I read wrong 1st post.
What ecu you have in the car? Without eeprom from ecu (for example i cannot sync petrol cars) will be pretty impossible to mare "ready to start" your dumps

[daten]

I read wrong 1st post.
What ecu you have in the car? Without eeprom from ecu (for example i cannot sync petrol cars) will be pretty impossible to mare "ready to start" your dumps

The engine ECU is Bosch EDC15M but I have no eerpom reading

[kiszka]

The engine ECU is Bosch EDC15M but I have no eerpom reading

if it's not a problem for you, check my file
original keys should work
https://mega.nz/file/wqJ0FbKT

if you haven't tried doing the sync then the car should work

[daten]

Hi everyone
Thanks for your help! The car started.
Synchro by obd with bmw scanner.
Too bad I couldn't test the files, but next time.


Greetings

[adielektro]

Hello, please help me. Bmw7 e38 2000r 3.0 diesel bosch edc15 0 281 010 314, 7 788 016, flash am29f400.
Bmw no crank, ews3 - dde, error not synchro. Will anyone read pin /ISN - flash 29f400.

[kiszka]

Hello, please help me. Bmw7 e38 2000r 3.0 diesel bosch edc15 0 281 010 314, 7 788 016, flash am29f400.
Bmw no crank, ews3 - dde, error not synchro. Will anyone read pin /ISN - flash 29f400.

isn is in eeprom 95p08

[adielektro]

ok, i will read and insert

[adielektro]

read by autel XP400 , eeprom 5P08c3

[adielektro]

1A 23 it is correct ISN ???
i read EWS , ISN - 1A 23
eeprom 5p08c3 - ISN -1A 23
Wire DDE/EWS it is OK. Key -OK.
Ews not errors, DDE has a fault -1DF5
Any idea ???