07 fiesta airbag

[adam28]

Hello guys,

One if one of you lads would be able to help me with this?
Would be greatly appreciated.

I got a 07 fiesta with a crashed airbag module.Its like one ive never seen before.Its a black sealed module, do i need to carefully cut a section out?Or can i read dump with correct pinouts with one of my programmers?
I dont know what Eeprom or Mcu is inside.
These are the numbers on the module
FoMoCo
60
6593637660
G1UHF
6S6T 14B056K
58603460594087
5WK4 3586
50060318

Thanks for any help

Cheers

Adam

[melmar]

have heard that people can do these from the pins but have never done it myself, i always cut a section out and desolder chip, if you look at ecu with writing facing you, cut a hole on the left side of the sticker, make the hole the same height as the sticker, and from the left edge of module to the edge of sticker. keep it as neat as possible then use hot air blower to melt back together and smooth it while its hot.. inside is 95160 chip, if you post file i have most files for these, these type of module is fitted in transit also...

[adam28]

have heard that people can do these from the pins but have never done it myself, i always cut a section out and desolder chip, if you look at ecu with writing facing you, cut a hole on the left side of the sticker, make the hole the same height as the sticker, and from the left edge of module to the edge of sticker. keep it as neat as possible then use hot air blower to melt back together and smooth it while its hot.. inside is 95160 chip, if you post file i have most files for these, these type of module is fitted in transit also...

Thanks that is great help, thanks for taking the time to explain.

I will post dump later.

Best regards

Adam

[adam28]

have heard that people can do these from the pins but have never done it myself, i always cut a section out and desolder chip, if you look at ecu with writing facing you, cut a hole on the left side of the sticker, make the hole the same height as the sticker, and from the left edge of module to the edge of sticker. keep it as neat as possible then use hot air blower to melt back together and smooth it while its hot.. inside is 95160 chip, if you post file i have most files for these, these type of module is fitted in transit also...

Here is crashed dump mate,from the 95160.

thanks again for everything.

Cheers

[juozas10]

Hello guys,

One if one of you lads would be able to help me with this?
Would be greatly appreciated.

I got a 07 fiesta with a crashed airbag module.Its like one ive never seen before.Its a black sealed module, do i need to carefully cut a section out?Or can i read dump with correct pinouts with one of my programmers?
I dont know what Eeprom or Mcu is inside.
These are the numbers on the module
FoMoCo
60
6593637660
G1UHF
6S6T 14B056K
58603460594087
5WK4 3586
50060318

Thanks for any help

Cheers

Adam

HI.
With carprog you can read or write dump in this procesor through obd2 conector. But you can also do it the way melerman said. Try this.

[adam28]

HI.
With carprog you can read or write dump in this procesor through obd2 conector. But you can also do it the way melerman said. Try this.

hi mate

Thanks for that, but i managed to do it with airbag resetter. didnt think it supported this module.

this is it,but slightly different to yours

Cheers

[melcool]

hi mate

Thanks for that, but i managed to do it with airbag resetter. didnt think it supported this module.

this is it,but slightly different to yours

Cheers

Have you managed with something else?

[adam28]

Have you managed with "crash eraser" or something else?

just desoldered 95160 erased with airbag resetter,job done.
Used x5 programmer from mcumall

[u.s]

do you have to de-solder the soic chip?
has anyone tried with something like this Programmers IN-CIRCUIT SOIC Test Clip (http://www.tek-tronics.co.uk/product_info.php?cPath=37&products_id=53)

[melmar]

from my experience you don't get a true reading with chip on the board, its easier to take it off and be sure of your readings...

[adam28]

do you have to de-solder the soic chip?
has anyone tried with something like this Programmers IN-CIRCUIT SOIC Test Clip (http://www.tek-tronics.co.uk/product_info.php?cPath=37&products_id=53)

And you may corrupt the eeprom too, then your fcuked! Or maybe not because someome on here will have a dump for you.
Just remove it mate,much safer.

[u.s]

thanks mate,
have no problem removing the chips but was just wondering if it can be done in-circuit.

[looly]

Hi all

Here is a very similar module....
Numbers are...

60
6593637660

G1UHF

6S6T 14B056 KC

58603470700835

5WK4 3586

13070310

I would be very grateful if someone could clear the crash data for me please.

Cheers

[juozas10]

Hi all

Here is a very similar module....
Numbers are...

60
6593637660

G1UHF

6S6T 14B056 KC

58603470700835

5WK4 3586

13070310

I would be very grateful if someone could clear the crash data for me please.

Cheers

Hi.
Try this crash data cleared.
Please report.
Best regards.:wink:

[looly]

Sorry guys, this is the dump that needs to be corrected....

Many thanks

[juozas10]

Sorry guys, this is the dump that needs to be corrected....

Many thanks

The archive is either in unknown format or damaged...
Please upload it again.
Best regards.

[looly]

I will try your dump juozas and post the outcome. Thanks for your help m8 :)

[mastaflex]

please can someone help me with a picture for how to open this type of airbag control unit


thanks

[Galee]

I know this is a old thread now but I have one to do also can anyone confirm this is the cut place on the ecu?
Many Thanks

[Galee]

Well here is a photo if anyone else needs it.

[duco]

Well here is a photo if anyone else needs it.
with carprog you can do this ecu without open, you only have to connect 3 wire on connector.
bye!
S5.4 - Airbag Reset Tool by diagnostic for Ford (http://www.codecard.lt/carprog/software/carprog-airbag/s5-4-airbag-reset-tool-by-diagnostic-for-ford/prod_81.html)

[morfej]

duco : But that's for bosh airbag's not siemens.

[laurentiudania]

Worked with Siemens 5WK4 3586 Fiesta 2005