RCD200 POLO MP3

[giruzzo]

POLO MP3 MADE IN KOREA VWZCZ5H0049654 HEL CODE

THANK YOU:wavey:

[juisro]

Hi, read dump 24c256 and post for the code.

[ppservis]

Please damp for RCD200 with known code,or code for my dump

[ppservis]

dump 24c256

[murat332]

dump 24c256

Code 1**2 see p.m.:ciao:

[Alex789]

Code 1**2 see p.m.:ciao:

If it's not so big secret for you, pls post code here.
This forum is great due to open information for all.

[murat332]

If it's not so big secret for you, pls post code here.
This forum is great due to open information for all.
hi alex
http://www.digital-kaos.co.uk/forums/f115/motorola-eeprom-cracker-94300/
MC68HC11PA8 how read shema need :ciao:

[jurkuc]

U must used programmer ETL, or interface on MAX232 with PCBUG11B ( dos mode ) and connect:

TxD - 1
RxD - 64
Reset- 61
ModA - 63
ModB - 62
+5V - 7 i 8
GND - 6, 33 i 41
pin 25: desolder,
change Qwarc 8 Mhz

[murat332]

U must used programmer ETL, or interface on MAX232 with PCBUG11B ( dos mode ) and connect:

TxD - 1
RxD - 64
Reset- 61
ModA - 63
ModB - 62
+5V - 7 i 8
GND - 6, 33 i 41
pin 25: desolder,
change Qwarc 8 Mhz
hello my friend thank jurkuc
friend winrar error: ( :vollkommenauf:

[jurkuc]

Ok, then try this:
or for faster PC.
Manual for this programm.

[murat332]

same problem my friend jurkuc
not understand :(
Thank you my friend jurkuc
ok no probem :)
regards

[siti]

my friend,use this interface,
pin9 rst to max -pin 61 to 11pa8

pin12rxd to max-pin 64 to 11pa8

pin11txd to max-pin 1 to 11pa8

ModA - 63 to gnd
ModB - 62 to gnd
+5V - 7 i 8
GND - 6, 33 i 41
pin 25: desolder,
change Qwarc 8 Mhz

but,mcu have security active not work

[siti]

to pcb carradio use this conection

[PremierD]

Code 1**2 see p.m.:ciao:

Ok mate ,First point ..You are not on Mobile Files ...(2) I you are going to help a poster ,fine we appreciate it .(3) If you want to PM the answer,then do it .without the cloak and dagger stuff,(4) Post the FULL number ..Or Nothing .This after all is the Sharing Forum.And you will help a lot more people ,if you do as asked .

Thank-you

[murat332]

my friend,use this interface,
pin9 rst to max -pin 61 to 11pa8

pin12rxd to max-pin 64 to 11pa8

pin11txd to max-pin 1 to 11pa8

ModA - 63 to gnd
ModB - 62 to gnd
+5V - 7 i 8
GND - 6, 33 i 41
pin 25: desolder,
change Qwarc 8 Mhz

but,mcu have security active not work
my friend many many thanks :ciao:
[to test and to report results]
regards


Ok mate ,First point ..You are not on Mobile Files ...(2) I you are going to help a poster ,fine we appreciate it .(3) If you want to PM the answer,then do it .without the cloak and dagger stuff,(4) Post the FULL number ..Or Nothing .This after all is the Sharing Forum.And you will help a lot more people ,if you do as asked .

Thank-you
Ok mate :ciao:
thank you
[my engilsh many bad]
regards