PDA

View Full Version : xprog read out B84N MC68HC11A1



el_futte
12th February, 2010, 05:18 PM
i have tryed 2 read out my B84N MC68HC11A1 from a peugeot 106 rally what family is this chip in i cant find it on device programmer desktop

and my progam just says device silenc ore bootloader error

Zmann
13th February, 2010, 03:46 AM
Try with the menu of A8, probably the old one. The difference amoung these two are the EPROM content which should not affect to the programming.

el_futte
13th February, 2010, 07:30 AM
argg my programmer xprog-t just says device silence and also whit a hc11f1 mcu

pinch
13th February, 2010, 12:43 PM
I get device silent trying to read E59B MC68HC11KA4 QFP64, I have desoldered it and try to read it with xprog-t ,have also tried to read it in circuit, no sucess.
Have you sucessed to read any MCU with your xprog-t ?

geniehex
13th February, 2010, 12:49 PM
I get device silent trying to read E59B MC68HC11KA4 QFP64, I have desoldered it and try to read it with xprog-t ,have also tried to read it in circuit, no sucess.
Have you sucessed to read any MCU with your xprog-t ?
HELLO
If you desolved the mcu you must add a cristal 4mhz or 8mhz!!

djdansmart
13th February, 2010, 01:08 PM
Also if you read in circuit be shure quartz from pcb is same as xprog software settings! In other case you need to setting from xprog software!

pinch
13th February, 2010, 01:19 PM
With the xprog it came a adapter for for HC11A8/E1/E9/E20/EA9, could I use that for the KA4 ?
It has a 8Mhz crystal on it.
How do I check the quartz from PCB ?

Regards

Added a pic of the PCB in question.

el_futte
13th February, 2010, 05:27 PM
no any luck there is a crystal whit the adapter there is follow 2 the device.. there is 7pcs adapter whit it ..

el_futte
13th February, 2010, 05:39 PM
its this one i have

Telwis.pl: XPROG-T HC12/HC11/HC08/HC05 Programmer [FULL SET] (http://www.telwis.pl/product_info.php/cPath/44_46/products_id/72/language/en)

pinch
13th February, 2010, 07:11 PM
I have the same.
HC11A8/E1/E9/E20/EA9 is the only QFP64 adapter for HC11.
I dont know if it works for KA4

el_futte
13th February, 2010, 07:13 PM
i have adapter hc11f1 and chip 2f37e its just says silence grrrrrrr

emekelektronik
13th February, 2010, 07:15 PM
Try other programmer!

el_futte
13th February, 2010, 07:25 PM
oder programmer??

el_futte
13th February, 2010, 07:26 PM
arg you mean Other programmer.. the first i have was xprog-m that dont work now this... and its not work eather

pinch
13th February, 2010, 07:29 PM
I didnt even get mine to read the X24C01 either....
is this programmer s**t ?
How many do you have to buy to get a working one ?
Have you managed to read anything with yours ?

el_futte
13th February, 2010, 07:50 PM
y manage eather 2 read a 23c04 ... i think its a very NOT nice programmer already ordre UPA programmer .

pinch
13th February, 2010, 08:33 PM
From where did you order your UPA ?
Think its any better ?
Need to buy i new one too

vares
13th February, 2010, 09:22 PM
Only one place for genuine UPA is
ELRASOFT Products (http://elrasoft.com/index.htm)

el_futte
13th February, 2010, 11:40 PM
what about adapters for hc11 and more for the upa???

pinch
16th February, 2010, 01:42 PM
I ordered a UPA-USB today, want to see if it works better then xprog-t

pinch
17th February, 2010, 08:25 PM
In the in circuit schematics for xprog-t it says XTAL pin XX;XX
Is assume that means crystal, but should I do something with that info ? Short, lift legs ?

mexanico1971
20th May, 2010, 05:46 PM
hi ! anyone successful read tms 374 and 28f256 width xprog? from obd factory ! my says bootloader initializing error ! the ecu in questan is a 1ap40 mm !

bricolo
20th May, 2010, 09:04 PM
I ordered a UPA-USB today, want to see if it works better then xprog-t

Hi
with UPA, to read MC68HC11A1 you must lift pins:
Reset, MODB, RxD and not desolder MCU

Zmann
21st May, 2010, 03:00 AM
hi ! anyone successful read tms 374 and 28f256 width xprog? from obd factory ! my says bootloader initializing error ! the ecu in questan is a 1ap40 mm !
Hi mate, Ive got the same too with the tms 374-28f256 ECU. If you followed the programmer-ECU connection instruction in Xprog-m TMS374 manual on the page of tms 374 and 28f256 you might notice that the instruction to connect Vcc to the ECU is missing. Make sure that you have connected it to 28F256 Vcc pin (pin32). hope this help.

subas
28th May, 2010, 09:02 PM
Hi. I trying to read MC68HC11L6 from audi gamma cc with xprog, no sucess. My programmer says bootloader initialising error. Im not desolder MCU, can anyone help me.
Thanks in advance.

mexanico1971
9th February, 2011, 04:10 PM
I'm doing a IAW 1AP40 again width xprog 4.5, all wires connect good , to read no need to connect the ac power and read it all the content, but wen make verify give bootloader ini error, if I put ac power says bootloader ini error from the start ! if I try to write give a lots of errors in buffer !
do anyone have some situation like this ?!
thank in advance

luiggii79
10th February, 2011, 12:26 PM
bootloader error posible the cristal frequency seting in the xprog menu