Clio IV Smok problem

[jurebv]

Greetings

have anyone experienced similiar issue and can give an advice,

using SMOK protocol RT0009 Clio 4 /Trafic III 2013-... OBD KM + blockade ABS on Clio IV 2015 , Ive used functions READ EE (eeprom) and READ FLASH (flash) with that protocol over obd before attempting mileage recalibration, after attempting mileage recalibration (and ABS Synchro block) dash shows ERROR PROG , i then proceeded to restore original eeprom and flash which succeded but dash is now resetting every 2 seconds, if i leave it for few mins like that with ignition off it stops but it shows ERROR PROG still and some lamps are on

Anyone experienced similiar issue? should i proceed to read on table with vvdi prog?

Yes i have tried taking battery out for few mins, nothing changes

ID photo in attach



Best Regards

[jomberykaso]

do it manually

[jurebv]

what do you mean manually? i can read by vvdi prog but there is comething corrupted and even restoring ori with smok doesnt help

I attach my flash read by smoke and read i found by someone online with vvdi prog, biggest difference is missing part of code from 38000 to 3BA00 in my file , i would try to copy this part but i assume checksums are required if i edit anything in flash

[drpeter]

what do you mean manually? i can read by vvdi prog but there is comething corrupted and even restoring ori with smok doesnt help

I attach my flash read by smoke and read i found by someone online with vvdi prog, biggest difference is missing part of code from 38000 to 3BA00 in my file , i would try to copy this part but i assume checksums are required if i edit anything in flash I compared the readed flash by smok file with a 2015 version it's exactly the same, i don't have a full flash dump to compare.

[jurebv]

Yes but dash keeps displaying prog error

here id with launch

[amar28]

Error prog on renault cars is eeprom corrupted

not sure how SMOK managed that as have done atleast 50 renaults on SMOK and never had this issue

did you select wrong option by mistake?

i dont think anything is missing from your flash, OBD flash is compressed and smaller than bench flash - You cant write
compressed flash by bdm either

Write eeprom from another cluster same P/N - see if prog error goes away

[Diagcar1]

Post your eeprom data, maybe I can compare it with files I have.

[Smart66]

Probably, E2P is corrupted so I think you need new calibration :(

[jurebv]

eeprom in attachment

how did anything got corrupted , these are obd reads BEFORE i attempted anything, do you mean the part of eeprom that is not in obd read? (Dflash)?

Eeprom read obd with smok in attacent

Dash keeps reseting constantly

[Panathaole]

maybe you have low battery voltage when programming?

[jurebv]

read with vvdi prog

[Smart66]

Are you clone Smok?

[jurebv]

original smok

[jurebv]

Solved, fixed eeprom myself, flash wasnt damaged

[honingkoning]

Are you clone Smok?Clone smok,or do you mean xtool [emoji3][emoji3][emoji3]

[brend]

Clone smok,or do you mean xtool [emoji3][emoji3][emoji3]

RT0009 litsens in smok and this is genuine tool .

[honingkoning]

RT0009 litsens in smok and this is genuine tool .
Duhhhhh clone smok was 10 years ago OR AM i missing something.

[brend]

Duhhhhh clone smok was 10 years ago OR AM i missing something.

First smok with old hardware yes and that's is for only old car not for new .

Last smok hardware only genuine .

[jurebv]

It was with genuine smok, i restored dash on my own and then done again with smok again, but this time i did abs too and without block synchro and it worked good

[brend]

It was with genuine smok, i restored dash on my own and then done again with smok again, but this time i did abs too and without block synchro and it worked good


Good job friend .