immo off edc15C2

[branco]

hi
need immo off edc15C2
flash AM29F400 attached
thanks

[melcool]

hi
need im*o off edc15C2
flash AM29F400 attached
thanks

for Citroen/Peugeot EDC15C2 immo adress in 8 pins ST95P08C3 (is on the other side of the board)

[busaman]

Read the file from 95p08. Open it and program from 0x0180 to 0x18F with value 0x00 .Then save the file and write it in 95p08 . That s all . The ecu is virgin and ready for new code .

[branco]

Read the file from 95p08. Open it and program from 0x0180 to 0x18F with value 0x00 .Then save the file and write it in 95p08 . That s all . The ecu is virgin and ready for new code .

thanks for reply friend
but was told that solution is inside flash 29F400
ecu EDC 15C2
one plug
bosh number: 0 281 010 567
THNAKS

[lupu_sandu]

For EDC15C2 im*o is in eeprom (95p08)
Read and post here

[branco]

For EDC15C2 im*o is in eeprom (95p08)
Read and post here


here it is friend
thank you to make it immo off
regards

[busaman]

try this it might work you did not say what engine it will need to be telecoded.

[branco]

try this it might work you did not say what engine it will need to be telecoded.


sorry
it is from peugeot 607
2.2 HDI diesel with FAP
136 cv
regards

[busaman]

i looked at both files it might work try it it wont hurt it will either work or not.

[branco]

i looked at both files it might work try it it wont hurt it will either work or not.


ok thanks
will try it and
and send resuts
regards

[melcool]

If the above dump dont work try this one!
Sometimes when you put dump from other(even same model) car you may get the Programming Error Fault and the ECU light in dash will be ON and the car will not accelerate above 2500-3000 rot...even the engine map is in Flash!

[branco]

If the above dump dont work try this one!
Sometimes when you put dump from other(even same model) car you may get the Programming Error Fault and the ECU light in dash will be ON and the car will not accelerate above 2500-3000 rot...even the engine map is in Flash!


thanks for help!
regards

[busaman]

If the above dump dont work try this one!
Sometimes when you put dump from other(even same model) car you may get the Programming Error Fault and the ECU light in dash will be ON and the car will not accelerate above 2500-3000 rot...even the engine map is in Flash!


i aggree if this happens you need dianostics to telecode.

[maaxxyy]

What tool do you use to read the 95p08?

[branco]

What tool do you use to read the 95p08?


hi
seeprog programmer
regards

[glk96000]

yes seeprog good programmer no probleme for read and write 5P08

[workas]

Read the file from 95p08. Open it and program from 0x0180 to 0x18F with value 0x00 .Then save the file and write it in 95p08 . That s all . The ecu is virgin and ready for new code .



Hi,is this version is same for EDC15 with one plug ECU and another with 3 pugs ECU?Both have inside 95P08C3 Eeprom.

[doddy2323]

Hi!Put the file 1 in eeprom and file 2 in flash.Work 100%.is tested.After that post feedback.

[workas]

Hi!Put the file 1 in eeprom and file 2 in flash.Work 100%.is tested.After that post feedback.
For witch version of ECU is thease files?With one Plug or with 3 plugs?

[doddy2323]

3 plugs tested on citroen and fiat

[workas]

3 plugs tested on citroen and fiat
I will test it tomorrow ok?

[workas]

Hi!Put the file 1 in eeprom and file 2 in flash.Work 100%.is tested.After that post feedback.


Don't working on my Xara Picaso 2.0HDI mine is EDC15C2
Bosch 0 281 010 595
Your is Bosch 0 281 010 346
With your Flash on my car no indication of glow plugs on dashboard ,car won't start.:mad:

[workas]

Don't working on my Xara Picaso 2.0HDI mine is EDC15C2
Bosch 0 281 010 595
Your is Bosch 0 281 010 346
With your Flash on my car no indication of glow plugs on dashboard ,car won't start.:mad:
There is my dump

[workas]

Maybe someone have Virgin Dump for Bosch 0 281 010 595 95P08,i will try ECU matching procedure with Lexia .Ill try to fill all dump with 00 and diagnostic writing that ECU are already mached -no possibility to match it again .
Maybe i need virgin eeprom and flash?

[crisssm]

i need a little help too i have a citroen xantia hdi with ecu edc15c2 0 281 010 627 and i want to make immo off completly i wil post dump and a free programer for the eeprom i modified the sources to support that memory (maybe the visual c++ runtime must be instaled )

[crisssm]

5p08 =1024 capacity in 2 pages fizicaly inside cip 95080 and other cips like this have 1024 in one page .so if u wil read 5p08 like 95080 the result wil be the first page readed twice . but with the program i uploaded it works .u can test it.
and for the 3 plug edc15c2 it is not enough to write the eeprom i tested all the variants possible .

[crisssm]

i had no succes whit the ecu with 3 connectors i am still trying . flash it with galeto or with kwp2000 . if somebody have one whit immo off and can read the flash and the eeprom maybe we can clone it . it may work

[tisser]

hello friends ihave a big problem in xsara hi lost a calculator and i make other new from peugot 406 edc15c2 i flash 29f400 with 5p08 original_0281 010 137.rar and now speed meter not move the car star but with limited aelerator im tryng a lot of firmware 29f400 an ,o chance please heeelp xsara 2000 90cv hdi vin VF1RHYB7304 ILOST THE ORIGINAL ECU FIRMWARE NUMBER HELP PLZ EDC15C2 ONE PLUG

[auto16]

HI IMMO OFF FOR 406 HDI 5P08 WORK 100/100
146259