PDA

View Full Version : Smart for two (451) tuning hardware?



strda50es
23rd February, 2010, 06:18 PM
Hi all.
Would like to know if someone could suggest me a semi pro or pro tuning tool for the new range (wme451) of smart cars.Any suggestion would be much appreciated.Thank you all in advance.

bynow3
22nd October, 2012, 11:32 AM
FGTech Galetto EOBD Master tested, diesel engines, works good

maglaras
22nd October, 2012, 03:22 PM
FGTech Galetto EOBD Master tested, diesel engines, works good
YES READ GOOD
PUT RITE BUDD:-((((:beheaded:

physyc
23rd October, 2012, 11:10 AM
No prob for writing....

donesko
23rd October, 2012, 11:58 AM
read only boot mode?

wsc
23rd October, 2012, 12:06 PM
and write also boot mode

audiomeca
24th October, 2012, 12:11 PM
AVDI ,WRITE right in petrol engine. Not tested in diesel

regards

bynow3
28th October, 2012, 03:35 PM
galetto 2 no need boot mode, as I remember... Neither for read nor for write...

donesko
29th October, 2012, 10:14 PM
galetto 2 no need boot mode, as I remember... Neither for read nor for write...

are you sure? can someone confirm this

physyc
29th October, 2012, 10:18 PM
why you need confirmation?

Plug it in try it. if not ok need boot mode.

No black magic, no rocket science...

donesko
29th October, 2012, 10:22 PM
why you need confirmation?

Plug it in try it. if not ok need boot mode.

No black magic, no rocket science...

i don't have interface

but in car list for galletto2

Smart 600/700 0.6/0.7l Bosch MEG 1.1 R/W -- BootMode+Flasher

wiseman
29th October, 2012, 10:24 PM
Read requires boot mode, writing doesn't. Galletto also reads EEPROM

TheBadFrog
25th September, 2013, 09:48 PM
Hi,which Kind of ecu has a smart model end of 2007 with gasoline Turbo 84 PS?Is it possible to clone the ecu? Or make immo off? Tuning file???Best regards

kennfeld
25th September, 2013, 11:47 PM
Hi,which Kind of ecu has a smart model end of 2007 with gasoline Turbo 84 PS?Is it possible to clone the ecu? Or make immo off? Tuning file???Best regards



it's ME 7.7.0 yes i can clone
changes 71 Hp mhd to 98 brabus


no you can't flash over obd protocols are kline and kline is not wired on the car
Stardiag do it over CAN H /L

filecloud
26th September, 2013, 07:38 AM
it's ME 7.7.0 yes i can clone
changes 71 Hp mhd to 98 brabus


no you can't flash over obd protocols are kline and kline is not wired on the car
Stardiag do it over CAN H /L

That is nonsense.
The 61/71hp is a normally aspirated car, the 98 Brabus is a turbo engine!
greetings,
filecloud

kennfeld
26th September, 2013, 08:54 AM
Why did you say it's nonsense it work car start on a 98 hp
ecu hw i 7.7.0 activation nasp or turbo is in eeprom
i flash internal and eeprom with the turbo car content then the nasp ecu become a turbo ecu
the car start while eeprom data matched to the customers SAM
i not tested the car on the road because client
it work the same as in other ecus boost control switch on/off ;)

i work on smart since before 98 before car release i have it in my hands at plant in hambach
i drove the roadster in december 2002 (released in april 2003 )
i have see 600 CC roadster ( the yellow prototype )

filecloud
26th September, 2013, 09:06 AM
:-)
You are right. Depending on the ecu.
But your postings sounds like you could TUNE a 71 to 98 hp.
Also do not forget that i tune smart since they exist. I am in business since 1980's. I have flashed smarts with etas prof and kic over obd even before superchips released their spi...
;-)

kennfeld
26th September, 2013, 09:15 AM
as you know a eeprom file is the computer car's boot .ini

inside you should find lot thing not always possible to understand by common human
programming date vin sw version ecu id hw or sw immo pin swcoding WSC etc etc an lot of switches that tell the ecu if you have activated speedlimiter etc

kennfeld
26th September, 2013, 09:18 AM
:-)
You are right. Depending on the ecu.
But your postings sounds like you could TUNE a 71 to 98 hp.
Also do not forget that i tune smart since they exist. I am in business since 1980's. I have flashed smarts with etas prof and kic over obd even before superchips released their spi...
;-)

you are right perhaps i explain bad
i said in r?ality that i affect a 71 ecu to a 98 hp car with installing the 98 hp data on the 71 hp ecu ecu run without dtc
not tested on road ... but i should soon

I programmed yet 451 petrol over obd but had some errors but perhaps now i have another file format
i can test again
perhaps CFF ;)