nissan nv200 crash data reset

[swa513]

hi i have carprog and it says required update is not active under the airbag/nissan section. i was able to read the chip in the epprom section but i do not know what data to zero out, could someone rest the bin for me i would appreciate it.

2015 nv200 98820 3LM0B 95128

[wti]

hello friend. test this one.

[swa513]

thank you for your help i will try it out asap

[superjet]

your tool read bad......
Use good tool read it or check your welding.
i dont know how his can clear it....

[swa513]

your tool read bad......
Use good tool read it or check your welding.
i dont know how his can clear it....


i tried a bunch of times with my carprog and i couldnt get it to read properly, i tried to use my autel508 and was able to read it as an st95128. hopefully this is good i program a lot of keys but this is new to me.

[superjet]

Your clear file.
report.no report no help next...
pass in your pm.

[swa513]

thank you i will let you know some time today

[swa513]

i just tried this and it gave me a code b1239

[superjet]

Crash is gone,you need check wireline or other parts without srs module,clear file only clear crash,no clear all dtc!

[swa513]

i appreciate your help i really do not know much about this stuff. before i flashed the module i had 4 codes B1209 frontal collision detection, B1035 crash zone sensor communication fault, B1051 driver airbag module circuit short to ground, and B1056 driver airbag module GND-short.

now it only has the one B1239 control unit and my autel unit does not give any specifics that it may be. i just got this van 2 weeks ago and the previous owner bought it rebuilt and drove it 5 years with locked seat belts and no front crash sensor the wires were just cut off. i fixed the belts with parts from junkyard seat belts (it did also have codes for both belts before i fixed it last week) and i got a front crash sensor from the junkyard from a versa with no body damage which is supposed to use the same part and soldered a connector on the wires. i will check the wiring tomorrow thank you

[superjet]

B1239 control unit？

[superjet]

Try this one,same pass

[swa513]

Try this one,same pass
when i click on the link i get this error from the site
You are not logged in or you do not have permission to access this page. This could be due to one of several reasons:

You are not logged in. Fill in the form at the bottom of this page and try again.
You may not have sufficient privileges to access this page. Are you trying to edit someone else's post, access administrative features or some other privileged system?
If you are trying to post, the administrator may have disabled your account, or it may be awaiting activation.

[swa513]

when i click on the link i get this error from the site
You are not logged in or you do not have permission to access this page. This could be due to one of several reasons:



You are not logged in. Fill in the form at the bottom of this page and try again.
You may not have sufficient privileges to access this page. Are you trying to edit someone else's post, access administrative features or some other privileged system?
If you are trying to post, the administrator may have disabled your account, or it may be awaiting activation.


dont know what changed but, it just let me download it, i will reply with results, thank you

[swa513]

i just tried the 2nd one and my scanner can not connect with the airbag module, it cant read codes and the airbag light is on.

[bolonc]

Try and reply..................


PASS=PM

[swa513]

i just tried this one and got the same result as superjet's error b1239 module and it will not connect with the scanner

[swa513]

does anyone have a stock factory one i could use?

[swa513]

does anyone have a stock factory one i could use?


i figured i would give it one more shot if someone can help me before i send it to a airbag repair place, if no one can help is there a reputable place i can send it to? thanks in advance