Peugeot 307 BSI

[nezocas]

Hello,

Car with flat battery and help this issue water inside BSI.
Water under relays and fuses support was taken care.

Car does not start.... diag says NO keys programmed, apparently coding was lost.... Owner does not have security code.

I have read the MC912DG128 with UPA......... VALEO GOX-00 ........ 9636760580 F ........... 9644098280 .......variante D
And also BDM files from ECU. ....... EDC16C3

Can someone check if files are good and not currupted.....????? And also need PIN from one of them to be able to program keys.

Best regards
Nezocas

[Andreastech81]

when your BSI is blank ...
the only place with PIN in memory is ecu
but your ecu eeprom file looks wrong
is eeprom 95160 ??

[nezocas]

is eeprom 95160 ??

I think it is.... but its inside the Mpc55 MCU

I had to make several attempts with galletto to be able to read eprom..... Flash and micro read without any problems the first time.

Regards

[Andreastech81]

ecu number ?

[nezocas]

Bosch
0 281 010 390
EDC16C3 47
96 465 601 80

[nezocas]

Photos of ECU and BSI
https://uploads.tapatalk-cdn.com/20221117/afe81cc1fb8bb4e201e0e5a49d746860.jpg

Enviado do meu 21061119DG através do Tapatalk

[nezocas]

BSI before repair https://uploads.tapatalk-cdn.com/20221117/27a6433645cac642b777f730d5f328a2.jpghttps://uploads.tapatalk-cdn.com/20221117/e2c0c5b99f0a794ea77af427693a709c.jpg

Enviado do meu 21061119DG através do Tapatalk

[Andreastech81]

open ecu ... try to find eeprom ST95160

unsolder it, read it ....

post here

[nezocas]

open ecu ... try to find eeprom ST95160

unsolder it, read it ....

post hereNo eprom inside

https://uploads.tapatalk-cdn.com/20221117/af06a73a9f87d943ea9aa0635d27e688.jpghttps://uploads.tapatalk-cdn.com/20221117/ff7d17ebdfdfb0906a8ebf7c99166a0b.jpghttps://uploads.tapatalk-cdn.com/20221117/518f7838b285e85b38db5de97a9f6ba8.jpg

Enviado do meu 21061119DG através do Tapatalk

[Andreastech81]

other side

[kiszka]

Hello,

Car with flat battery and help this issue water inside BSI.
Water under relays and fuses support was taken care.

Car does not start.... diag says NO keys programmed, apparently coding was lost.... Owner does not have security code.

I have read the MC912DG128 with UPA......... VALEO GOX-00 ........ 9636760580 F ........... 9644098280 .......variante D
And also BDM files from ECU. ....... EDC16C3

Can someone check if files are good and not currupted.....????? And also need PIN from one of them to be able to program keys.

Best regards
Nezocas
if you want to recover original keys
then you have to go to the nearest service center for a PIN with a set of documents from the vehicle
with the owner of the vehicle
there is no other option
if you don't care about the original keys, I can set any pin in the ecu, and you'll be able to deal with bsi
or buy a starter kit with keys

[rafal]

if you want to recover original keys
then you have to go to the nearest service center for a PIN with a set of documents from the vehicle
with the owner of the vehicle
there is no other option
if you don't care about the original keys, I can set any pin in the ecu, and you'll be able to deal with bsi
or buy a starter kit with keys

not now................they will say for leave car with them
as you said - starter kit or set of dumps + learn new key

[nezocas]

Found that sucker... Hidden on the other side

[nezocas]

Found it.... lets hope we have a full functional ecu after.... no easy task to open

[rafal]

Found that sucker...

??????????????????????
pin: HVXQ
recode by lexia..................

[Andreastech81]

agree with rafal

pin code HVXQ or QXVH :)

[kiszka]

.............
925441

[nezocas]

Hello,

When I try to put the 4 digit code to learn the key to the car.... it say´s Immoblizer Locked.....wait 20 minutes.
Also engine ECU is in Locked state.

Will investigate futher.

Regards

[kiszka]

Hello,

When I try to put the 4 digit code to learn the key to the car.... it say´s Immoblizer Locked.....wait 20 minutes.
Also engine ECU is in Locked state.

Will investigate futher.

Regards
bsi must be virgin

[rafal]

Hello,

When I try to put the 4 digit code to learn the key to the car.... it say´s Immoblizer Locked.....wait 20 minutes.
Also engine ECU is in Locked state.

Will investigate futher.

Regards

Have you wrote my file to bsi?

[nezocas]

Have you wrote my file to bsi?

yes...

but always say immo locked, I was only able to place vin inside with lexia

[drz]

FIRST you have to programm pin in virgin bsi, than programm key and you will start the car. After you have to do all configuration in bsi...

[nezocas]

Ok, I understand all the procedur.e
But I am only able to input the VIN and the BSI says vin coded correctlly.
When trying to learn the BSI... she first askes for the security code..... I place it and hit enter.... And she says: BSI is virgin, make learning first.

Will source a scrap yard donner

Enviado do meu 21061119DG através do Tapatalk

[Andreastech81]

hmm ... i think you are somekind a bit of a lost ...

first in PP2000 at your left of your screen (where the VIN should display) are all bbbbbbbbbbbbbb ???? or not ???

second, when your BSI is blank ... to starting coding, when you replace BSI,
you have to go at "replacement parts" menu (not diagnosis) and tell the PP2000 that the BSI is replaced,
right after that the PP2000 will ask you to put the VIN and the PIN from the car

last step is coding BSI and program immo chips

P.S all that i am telling by memory, don't ungry to me if a miss any step. :)

[nezocas]

Hello,

Got a BSI from scrapyard, same part number, from same car and engine code.
Now I need to get the pin from this dump, with that I will be able to program the keys.... and VIN.
Or better....make it virgin to be able to adapt to the car

Regards
Nezocas

[nezocas]

Made virgin myself....
Lets try and hope its good.

Regards

[aceton]

Lexia ask pin 4 or 5 signs ?

[rafal]

Lexia ask pin 4 or 5 signs ?

i never seen in psa login of 5 ...................

[nezocas]

Hello,
Car is running, made a copy of the fully programed BSI to the old one, and car doesnt start..... old one is garbage.
You need to do the folloying:
config of services and calculators
test by calculator
bsi
config
client options
show room
change from client to factory
go back and exit PP200
enter again and chose replacement parts
Bsi
and follow until the end

Only thing that isnt still working is the remote locking and unlocking of the car, I made ignition to ACC, press lock button on remote for 10 sec, remove key, wait 10 seconds and press lock again.
Maybe is uncorrect coding under central locking in the BSI???

Regards

[aceton]

Adaptation pin 03114 ?

[Crasftsman]

Adaptation pin 03114 ?

This code "03114" only works on citroen.
Peugeot doesn't use this number"03114" for configurations alterations, this one or any other number.