Clear crash ford focus

[GolfmkI]

Ford focus airbag :

4M5T 14B056 BF
bOSCH 0 285 001 552


It is first time i read an airbag dump, I have read 95080. My dump is correct???

Anyone could told me a software, so that I could Know what bytes must I modify??

When I obtain I modified dump, I may erase old one? And write all dump? Only modify some lines?

This is my dump, any help will be appreciated.

I have included both formats hex and bin, what is the most common to use.???

Lot of questions I have!!!!!!!!!:devil:

[melcool]

Try this and post results

[GolfmkI]

Ok I will try, but one question why it is not the same size???
I suposed it will be a 1.024 bytes file too???

[GolfmkI]

I have tried using Tachosoft 6.4 and gives me a dump with exactly 1024 bytes, yours have more bytes.

I have read that tachosoft it is not very exactly, but ..........tomorrow I will tell you, I will try first with yours and if it not work then I will try with dumo that give me tachosoft.

[melcool]

My dump size no good! I see now!
Try these!

[GolfmkI]

Then , so I can learn......size must be equal in original and modified dump???

Always?

Very thanks for your help, really.

[melcool]

NO, your knowledge was good! My BAD :vollkommenauf: Try now the above!

[GolfmkI]

No problem, then I will try with dumo that give me tachosoft...
curisity what software do you use for this works???

Really very thanks.:devil:

[GolfmkI]

Hello I think the dump I have read it is not correct I have been watching similar dumps, and it sees vin number and etc....in mine dont see any clear.

I have read 95080 in circuit, with oscilator bridged, it is possible ??? May I remove eeprom to read better???

Now my only solution is someone could share with me some original dump, crashed or not crashed of the same unit exactly the same so I could compare .

I atach my original dump, can anyone tell me if it is a valid dump???


If not where can I find dump for

4M5T 14B056 BF
0 285 001 552
650018471801( Is this last number important???) I have lot of dumps but dont match with this number rest of reference are the same.

Very thanks for your help.

[GolfmkI]

Anyone???
I have dumps that i download from this forum but it does not is the same number it says
4M5T 14B056 BF
0 285 001 552 but the other number are not the same, can I use it???


Thanks

[lupu_sandu]

Your dump cleared.
This is dump from you, witch have been cleared.
No other dump

[GolfmkI]

Thanks, but I am not sure that me dunp read, it is correct!!!!!! Because I have read 95080 in circuit, and i have seen that every time I read ort write different values appear, so i am almost sure that it is not a correct dump, so cleared dumps will not too???


Is there any way to check if my original dump is ok?

Thanks in advice.

[juozas10]

Thanks, but I am not sure that me dunp read, it is correct!!!!!! Because I have read 95080 in circuit, and i have seen that every time I read ort write different values appear, so i am almost sure that it is not a correct dump, so cleared dumps will not too???


Is there any way to check if my original dump is ok?

Thanks in advice.


Hi.

Is no correct read dump!!!!!! This is an example.
Remove eeprom,and read once more...

Best regards.

[GolfmkI]

Hi.

Is no correct read dump!!!!!! This is an example.
Remove eeprom,and read once more...

Best regards.

I cannot read again, because I have erased to program it with modified dump, so I have not original dump.

This one that you have post is mine or it is another.
ONly I need is an original dump ok of this ecu crashed or cleared..

[GolfmkI]

Ok I see cannot use your dump, its not the same.......or really could I use it?

mine :

4M5T 14B056 BF
0 285 001 552
650018471801

dump that you posted differs in last line

[juozas10]

Ok I see cannot use your dump, its not the same.......or really could I use it?

mine :

4M5T 14B056 BF
0 285 001 552
650018471801

dump that you posted differs in last line


You need remove eeprom...you need good read...you need save original dump...you need fix the original dump then it will works...
Try this,crash data was cleared 100%, but other last foult are clearing by diagnostic, please report.Good luck.

Best regards.

[melcool]

Try these and post results!

[GolfmkI]

Thanks to all your dumps. but i have a doubt.........
Mine is 4M5T 14B056 BF
0 285 001 552
650018471801

but last number line is not important??? 650018471801
May I programm even if last number it is not the same???

All dumps that you have posted has other number,other references are ok, but last number is different.