If your box as gone into klein system and will not boot up then you need this program>>>>>>>>>>>Digital Kaos - Downloads - Image Flashing assistant this will refresh your image just follow the guide from post 1 that should sort you out.
-
-
Thanks, but I downloaded IFA a few days ago and it hangs like this below when I try to flash the last working image back.
?debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.1 mID 03
debug: feID 00 enxID 03
debug: fpID 52 dsID Hallenberg.com
debug: HWrev 41 FPrev 0.23
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
debug: autoboot aborted from terminal
dbox2:root> boot net net net net net net net net net net
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Got BOOTP reply from Server IP 169.254.68.148, My IP 169.254.68.202
debug: Sending TFTP-request for file u-boot
will verify ELF image, start= 0x800000, size= 140064
verify sig: 262
boot net: boot file has no valid signature
Branching to 0x40000
U-Boot 1.3.4 (Tuxbox - Hallenberg.com) (Nov 29 2008 - 23:53:59)
CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Sagem, BMon V1.1
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
BOOTP broadcast 5
Retry count exceeded; starting again
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
BOOTP broadcast 5Comment
-
Have you tried flashing a different image as this might be corrupt. I don't know much about boot logs as i use just a xover cable. Are you sure the image is fine?Comment
-
Thanks gizmo i have also tried a backup image am going to reboot everything and try againComment
-
Just uploaded the file and a tut for flashing using a null modem. Might be of use to someone.
THE TRUTH
The Hillsborough Independent Panel. 12/09/12
Today's report is black and white.The Liverpool fans were not the cause of the disaster.
The panel has quite simply found 'no evidence' in support of allegations of 'exceptional levels of drunkenness, ticketlessness or violence among Liverpool fans' and 'no evidence that fans had conspired to arrive late at the stadium' and 'no evidence that they stole from the dead and dying'.Comment
-
hey guys, im trying to connect the dbox to hyper terminal. but when its comes to setting up a connection, i cannot change the country/region, its stuck on uruguay (598) or the area code.
can anyone help??Comment
-
hyperteminal
hi mate got a bit stuck here foolow u instructions but when transfering the image it onlt take about 7 secs any ides
HAD THE PARTY LOLComment
-
hi there,
I have done everything as explained in this guide.there is a slight problem at the end.It says at the last step when i tyepd in cp.l 120000 10020000 1F8000 enter
it says
copy to flash ....Flash not erased
=>
and it does not say done after 2 mins not even after waiting 10 mins
Please advise me with ur experience and knowledge.
thanx a lot and regardsComment
-
Hi there,
I recently tried this and the mistake I was during the 'transfer file' part. Make sure you are using the correct transfer protocol. One file you need to transfer as 'text file' and the other as 'file'
Hope this makes sense.Comment
-
Don't think it matters. It greys out when you select your com port.Last edited by RayR33; 9 February, 2009, 21:56.Comment
-
dbox flashing
tryed everything all goes well till near the endComment
-
I have a d digital box will this guide work on that as ive tried and all i get is the hypo terminal flashing curser no info goes on?
Thx ClaireComment
-
hyperterminal
where or how do i get a hyperterimal im new to this game please help
Comment
Comment