Here's a quick guide on how to transfer the nagrarom7 file using FTP.
What?s required - HARDWARE:
1. DBox2
2. RJ45 Network Crossover cable. (NOT an ethernet cable)
3. PC (this was done using windows XP) with a network card.
What?s Required ? SOFTWARE:
FTP program eg. ?Flash FXP? (30-day trial version works fine).
Let?s Get Started:
To make this easier, place your tv/box close to your PC
(so that you have easy access to the back of both, to change cables around.)
1. PC Setup: Now would be a good time to create a ?System Restore Point? on your PC,
(as you will have probably have to change the IP settings, to something different from your internet settings).
Unplug your internet connection NOW to avoid any conflicts.
Switch OFF all firewalls and antivirus on your PC
(and make sure windows XP built in firewall is OFF)
2. Power on the TV and DBox, but don?t hook it up to your PC yet.
Using the remote control, press DBOX > SETTINGS > NETWORK
Take a note of the DBox network settings
(this is an example only)
IP-Address 192.168.0.3
Net Mask 255.255.255.0
Broadcast 192.168.0.255
Def Gateway 192.168.0.2
Name Server 192.168.0.2
3. On the PC go to START BUTTON > SETTINGS > CONTROL PANEL and open the NETWORK CONNECTIONS
Right-click the network card (it may say Local Area Connection),
and select PROPERTIES > CONFIGURE > ADVANCED tab
Highlight the ?Connection Type? (in the left window),
and in the right ?Value window there is a drop down menu (it will probably currently say automode)
Change the Value to 10 full mode then OK
Again, right-click the same connection, and go back into the PROPERTIES of the network card
There is a List of items in the first window (you may need to scroll down further)
Left-click on internet protocol, when it is highlighted, click the PROPERTIES button.
Select the ?Use the following IP address?
Enter the settings, as you seen it on your DBox, except the IP address will be one digit less of the last number
(eg. 192.168.0.3 on DBox, so use 192.168.0.2 on your PC)
OK these settings.
4. Connect the RJ45 cable between PC and DBox (linking them together)
Run the Flash FXP program
On one side should be the files on the PC
On the other side make sure you select ?ftp browser? (the tab is a monitor and folder picture)
(It may already be selected)
Click CONNECT (the icon which looks like a lightening bolt)
Select QUICK CONNECT the three boxes require some information
SERVER OR URL = (enter the IP address of the DBox)
USERNAME = root
PASSWORD = dbox or dbox2 or commando
Then click CONNECT
You should now see the DBox files in the window (if not, check the IP settings/password).
5. In the PC file window, browse to the folder containing the nagrarom7 file.
In the DBox window browse to the var/keys folder (NOTE: you may already be in this folder).
Transfer the nagrarom7 file across into the var/keys folder
Delete any other nagrarom(10/11... etc) files
When done close down the Flash FXP program.
You may need to Enable Autoupdates on your Image (search forum on how to do this).
Now reboot the DBox
Switch to a non-FTA channel. Wait a few minutes for codes to update.
6*. You may want to use the ?System Restore? program now, on your PC,
Select ?Restore To An Earlier Time? and choose the correct point
Turn back ON your firewall, and virus checker
this is the work of some1 else but i found it very helpfull
What?s required - HARDWARE:
1. DBox2
2. RJ45 Network Crossover cable. (NOT an ethernet cable)
3. PC (this was done using windows XP) with a network card.
What?s Required ? SOFTWARE:
FTP program eg. ?Flash FXP? (30-day trial version works fine).
Let?s Get Started:
To make this easier, place your tv/box close to your PC
(so that you have easy access to the back of both, to change cables around.)
1. PC Setup: Now would be a good time to create a ?System Restore Point? on your PC,
(as you will have probably have to change the IP settings, to something different from your internet settings).
Unplug your internet connection NOW to avoid any conflicts.
Switch OFF all firewalls and antivirus on your PC
(and make sure windows XP built in firewall is OFF)
2. Power on the TV and DBox, but don?t hook it up to your PC yet.
Using the remote control, press DBOX > SETTINGS > NETWORK
Take a note of the DBox network settings
(this is an example only)
IP-Address 192.168.0.3
Net Mask 255.255.255.0
Broadcast 192.168.0.255
Def Gateway 192.168.0.2
Name Server 192.168.0.2
3. On the PC go to START BUTTON > SETTINGS > CONTROL PANEL and open the NETWORK CONNECTIONS
Right-click the network card (it may say Local Area Connection),
and select PROPERTIES > CONFIGURE > ADVANCED tab
Highlight the ?Connection Type? (in the left window),
and in the right ?Value window there is a drop down menu (it will probably currently say automode)
Change the Value to 10 full mode then OK
Again, right-click the same connection, and go back into the PROPERTIES of the network card
There is a List of items in the first window (you may need to scroll down further)
Left-click on internet protocol, when it is highlighted, click the PROPERTIES button.
Select the ?Use the following IP address?
Enter the settings, as you seen it on your DBox, except the IP address will be one digit less of the last number
(eg. 192.168.0.3 on DBox, so use 192.168.0.2 on your PC)
OK these settings.
4. Connect the RJ45 cable between PC and DBox (linking them together)
Run the Flash FXP program
On one side should be the files on the PC
On the other side make sure you select ?ftp browser? (the tab is a monitor and folder picture)
(It may already be selected)
Click CONNECT (the icon which looks like a lightening bolt)
Select QUICK CONNECT the three boxes require some information
SERVER OR URL = (enter the IP address of the DBox)
USERNAME = root
PASSWORD = dbox or dbox2 or commando
Then click CONNECT
You should now see the DBox files in the window (if not, check the IP settings/password).
5. In the PC file window, browse to the folder containing the nagrarom7 file.
In the DBox window browse to the var/keys folder (NOTE: you may already be in this folder).
Transfer the nagrarom7 file across into the var/keys folder
Delete any other nagrarom(10/11... etc) files
When done close down the Flash FXP program.
You may need to Enable Autoupdates on your Image (search forum on how to do this).
Now reboot the DBox
Switch to a non-FTA channel. Wait a few minutes for codes to update.
6*. You may want to use the ?System Restore? program now, on your PC,
Select ?Restore To An Earlier Time? and choose the correct point
Turn back ON your firewall, and virus checker
this is the work of some1 else but i found it very helpfull