https://www.digital-kaos.co.uk/forums/ en Mon, 08 Jun 2026 20:40:14 GMT vBulletin 60 https://www.digital-kaos.co.uk/forums/images/misc/rss.png https://www.digital-kaos.co.uk/forums/ https://www.digital-kaos.co.uk/forums/the-garage/airbag-chiptuning-dash-ecu-immo-locksmith-radio-satnav/guides-procedures-tutorials-aa/9181624-volvo-v40-t5-5-cylinder Fri, 05 Jun 2026 18:01:43 GMT Who can help me with synchronization of ecu - cem modules. Car battery off for 6 months. Thank you. Who can help me with synchronization of ecu - cem modules. Car battery off for 6 months. Thank you. Allesreg https://www.digital-kaos.co.uk/forums/the-garage/airbag-chiptuning-dash-ecu-immo-locksmith-radio-satnav/guides-procedures-tutorials-aa/9181624-volvo-v40-t5-5-cylinder https://www.digital-kaos.co.uk/forums/the-garage/airbag-chiptuning-dash-ecu-immo-locksmith-radio-satnav/guides-procedures-tutorials-aa/9176973-ddcr-delphi-ecu-reading-eeprom-95080-without-damaging-the-case Wed, 27 May 2026 18:01:50 GMT Delphi 8200334419 8200374152 DDCR Megan 1.5dci Searching the NET for working with this computer, all the craftsmen cut the plastic casing to get to... Searching the NET for working with this computer, all the craftsmen cut the plastic casing to get to the Eeprom or Flash memory. My guide is how I managed to read and write the eeprom without damaging the casing for Immo off or cloning the ECU for replacement. I tried with three or four Flash programmers to read the computer on the workbench outside the car without success. These ECUs exist in several versions (I think THREE). Infenion MPC SAK-C167C with external memory -FLASH 29F200BB- or FLASH ST10F275 or with MPC 55x/56x which is read by Jtag or BDM. We do not know this data until the printed circuit board is physically removed because all the elements are on the underside of the board and are not visible. You can either cut the plastic casing or unsolder about a hundred pins (who has adequate equipment and knowledge) which is risky from damaging the board. I will post pictures of how I successfully read and wrote the Eeprom without damage. You can do immo off or copy from the original ECU to the donor. Just remove the aluminum cover and solder the wires to the shown pins. With fine sandpaper or a thin drill, remove the varnish and solder the thin wires that are connected to the DIL 8 connector that is placed in any programmer that reads the 25/95 series of eeproms. The content is read and copied to the donor computer. The only work left is coding the nozzles. The easiest way is to read the nozzle data with a regular diagnostic and manually enter it into the donor ECU. (Autocom, Launch, Delphi ......).
Immo Off in the addresses from 00000-00018 write FF and that's it....
View the pictures and you can use them to


Usually if none of this works, the only option left is to physically remove the chips and place them in programmers that can read and write them. This way, the problem can always be solved as a last resort or if you don't have an adequate programmer. By physically replacing the chips]]> RadovanPetkovic https://www.digital-kaos.co.uk/forums/the-garage/airbag-chiptuning-dash-ecu-immo-locksmith-radio-satnav/guides-procedures-tutorials-aa/9176973-ddcr-delphi-ecu-reading-eeprom-95080-without-damaging-the-case https://www.digital-kaos.co.uk/forums/the-garage/airbag-chiptuning-dash-ecu-immo-locksmith-radio-satnav/guides-procedures-tutorials-aa/9174958-delphi-autocom Sun, 24 May 2026 08:39:33 GMT mercmedics https://www.digital-kaos.co.uk/forums/the-garage/airbag-chiptuning-dash-ecu-immo-locksmith-radio-satnav/guides-procedures-tutorials-aa/9174958-delphi-autocom https://www.digital-kaos.co.uk/forums/the-garage/airbag-chiptuning-dash-ecu-immo-locksmith-radio-satnav/guides-procedures-tutorials-aa/9173957-coding-high-beam-assist-fla-on-bmw-g21 Fri, 22 May 2026 08:19:55 GMT It's possible coding High Beam Assist (FLA) function with INSTA or similar, the car is predisposed but it must be activated:

Thanks in advance

]]> ginodilegno10 https://www.digital-kaos.co.uk/forums/the-garage/airbag-chiptuning-dash-ecu-immo-locksmith-radio-satnav/guides-procedures-tutorials-aa/9173957-coding-high-beam-assist-fla-on-bmw-g21 https://www.digital-kaos.co.uk/forums/the-garage/airbag-chiptuning-dash-ecu-immo-locksmith-radio-satnav/guides-procedures-tutorials-aa/9170336-2025-jeep-grand-cherokee-bcm-p68608712af-clone Fri, 15 May 2026 16:54:05 GMT Hello does anyone know what device can clone ST SPC58 mcu that is fitted inside this bcm... original bcm is water damaged but still starts jeep.. New... Hello does anyone know what device can clone ST SPC58 mcu that is fitted inside this bcm... original bcm is water damaged but still starts jeep.. New BCM is on national back order here in the USA.. attach are some pictures . Any help is appreciated.. alex_r_2001 https://www.digital-kaos.co.uk/forums/the-garage/airbag-chiptuning-dash-ecu-immo-locksmith-radio-satnav/guides-procedures-tutorials-aa/9170336-2025-jeep-grand-cherokee-bcm-p68608712af-clone