MPPS

**noriginal** · 24th February, 2011, 08:54 PM

today have write ivenif problem a bmw x5 edc16c31
read 1mb file, have mod with map3d and write

no problem, this is seven bmw that i read and write
my mpps is version with box
work perfect with bmw cars

**Marmes** · 24th February, 2011, 11:08 PM

many people don't know how to assemble mpps. If you go by those images you will burn it.

**MMichael** · 25th February, 2011, 02:53 AM

Originally Posted by bazare

good luck with building your MPPS based on my photos

what is scratched is SJA1000T and c8051F340

If you or anyone else could post the requested USBViewer screenlog, to know the basic usb descriptor. And then later i would need SnoopyPro usb traffic logfiles. I don't say its easy or succsess is guaranted, but worth a try and intressting enough to try. Uh, and by the way would not be the first time that i had 'luck' cloning a usb device without a dumpfile.

**elchip** · 25th February, 2011, 08:10 AM

Originally Posted by MMichael

If you or anyone else could post the requested USBViewer screenlog, to know the basic usb descriptor. And then later i would need SnoopyPro usb traffic logfiles. I don't say its easy or succsess is guaranted, but worth a try and intressting enough to try. Uh, and by the way would not be the first time that i had 'luck' cloning a usb device without a dumpfile.

Here for all who need with manual :

http://www.sendspace.com/file/66ymqh

Regard's

**bazare** · 25th February, 2011, 12:22 PM

Originally Posted by MMichael

If you or anyone else could post the requested USBViewer screenlog, to know the basic usb descriptor. And then later i would need SnoopyPro usb traffic logfiles. I don't say its easy or succsess is guaranted, but worth a try and intressting enough to try. Uh, and by the way would not be the first time that i had 'luck' cloning a usb device without a dumpfile.

What can I say? Good luck ... making this clone without the dump in the MCU

**bts** · 26th February, 2011, 09:52 AM

Mpps version:5.08 ,
Software version:3.0.3.38 ,
seri:41323234

What is the problem?

**bazare** · 26th February, 2011, 02:46 PM

New sw version 5.0.1.2 for genuine mpps
hyunday i30 added
after installation run the firmware update in the mpps folder.

**SEr** · 26th February, 2011, 04:04 PM

Read AUDI A4 with EDC17. Considered only calibrations. Not the full.
I can not attach a file.

**Tereksaz** · 1st March, 2011, 04:34 PM

Originally Posted by bazare

What can I say? Good luck ... making this clone without the dump in the MCU

ye!
You right!

without dump C8150f340 , without ID device and without Unit Key and without counter Key, NOBODY dont make Interface for MPPS.
I am kill a lot off time for it - and close it's project to version 3.02.37!!!!
Now - I do not have time to crack MPPS on.
At another time - buy the official adapter - and then completed yet.
Good luck! guys!

**Mrjitter** · 1st March, 2011, 07:08 PM

Originally Posted by Tereksaz

ye!
You right!

without dump C8150f340 , without ID device and without Unit Key and without counter Key, NOBODY dont make Interface for MPPS.
I am kill a lot off time for it - and close it's project to version 3.02.37!!!!
Now - I do not have time to crack MPPS on.
At another time - buy the official adapter - and then completed yet.
Good luck! guys!

Hi ..

But ....... the boot dump was post in this thread and we know where put the serial number . Only we need know where put the ID and counter ,is that correct ???

Regards

**bazare** · 1st March, 2011, 09:09 PM

Originally Posted by Mrjitter

Hi ..

But ....... the boot dump was post in this thread and we know where put the serial number . Only we need know where put the ID and counter ,is that correct ???

Regards

Wrong! Try to flash that dump and you will see how it doesn't work

**Mrjitter** · 1st March, 2011, 09:52 PM

Ufffffffff .... i don?t understand .. in reply #916 and 998 could see .....

Originally Posted by tehnosoftex

If you will have the bootloader you will have all the dump because when you will start the program, if it see the bootloader , it start to update the flash, and voilla, you will have all the dump. You are clever.

-----------------------------------------------------

Originally Posted by Tereksaz

write dump - very easy!
1. start - new file - sise 64kb
2. place bootloader
3 find start address flash and place it.
4. find start adderss serial number and place key and ID
Vualay - flash is done!
programming MCU c80512f340 - and you have Interface = MPPS.
today ,only , not high 3.0.2.37 .
Tomorrow - I am think and 4.x.x.x
==================
=AZ=

Regards