.>>>>>>>>>>>>>>>>>>Xhorse Multi Prog<<<<<<<<<<<<<<<<<<<

[sniegavirs]

Opel Delco E98
BENCH - Does not work. It reads the ID fine with all SW numbers but cannot read it.
BOOT - Does not work. After read error it asks for password (OK that could be normal but there is no option to read the password in Bench or OBD - so useless..) And after you cancel that operation Multi Prog device hangs up and only way is to restart it with power switch.

Also for some ECU's the Pinout information is confusing that could lead to burned HW (ECU/TCU or Multi Prog) where pinout picture is correct but top right pinout legend is numbered wrong.
Also there are a lot of ECU's listed where inside memories are shown 0 and is not working.
For example take Scania EMS S8 ECU
Only option is BOOT. Pinout for external connector is correct but there is no information about actual BOOT connection on PCB where 3 wires should be connected near MCU.

They are advertising this as ECU/TCU read/write/clone tool but it is very half-baked product at the moment.

[mikajna]

VW Golf 5 GTI MED9.10 NOT work, cant connect to ecu

[sharpshooter86]

VAG EDC17CP14
INT EEPROM READ
INT FLASH READ
EXT FLASH Read data failed! Ending process

The chip power has been turned off!

[sv2hqx]

VAG EDC17CP14
INT EEPROM READ
INT FLASH READ
EXT FLASH Read data failed! Ending process

The chip power has been turned off!

same on edc17c57

[lupu_sandu]

Last update bring RH850 VAG to multi-prog
What cable do we use? Same RH850 cable as Pad?

[sniegavirs]

Last update bring RH850 VAG to multi-prog
What cable do we use? Same RH850 cable as Pad?

No. There will be new cable. Not available at the moment..

[sharpshooter86]

with Databse update V17 MED 9.1 now can read

[lupu_sandu]

Read 2 read BCM from Porsche = ok, no need to remove components (same schematics as hextag).

[sniegavirs]

V19 - BMW CAS3+ Mask 0L15Y - Multi PROG sometimes struggles to crack the MCU. Sometimes the cracking takes a long time and sometimes it fails. VVDI Prog does it instantly very time you press read or write.

[MACKIE]

Any news about the cable for RH850 ?

Regards
Mackie

[tepSIJA]

Any news about the cable for RH850 ?

Regards
Mackie

[In stock] XHORSE XDNPR8GL MQB RH850/V850 Adapter for VVDI Key Tool Plus


https://www.vvdishop.com/wholesale/x...0-adapter.html

[MACKIE]

That is adapter for vvdi key tool plus not for multiprog.

Regards
Mackie

[sniegavirs]

[In stock] XHORSE XDNPR8GL MQB RH850/V850 Adapter for VVDI Key Tool Plus


https://www.vvdishop.com/wholesale/x...0-adapter.html

He asked about RH850/V850 Adapter cable for Multi PROG not Key Tool Plus!!! This is Multi PROG thread!!!

[qwojtus]

V19 - BMW CAS3+ Mask 0L15Y - Multi PROG sometimes struggles to crack the MCU. Sometimes the cracking takes a long time and sometimes it fails. VVDI Prog does it instantly very time you press read or write.

You right. It read quickly than took ages to write it back, about a minute crack the CAS3 chip.

Also if you read, no any possibilities to see the data or edit anything. Big upgrade of nothing.

Competition like Obdstar or CGDI or Hexprog much more useful in ordinary staff, but obviously no that fully packed with thousands options like multiprog

[sniegavirs]

V19 - Ford Continental SID211
Bench - ID good, reading does not work.
Boot - does not work, no ID and also it would not be possible to read because there is no option to read the MCU Password and Boot connection on PCB is wrong.