2007 ford galaxy crash data

**obdmaster** · 1st April, 2010, 01:45 PM

A friend has just bought an accident damaged 2007 ford galaxy, which hes repaired and replaced both seat belt pretensioners, airbag light is on with code U1A3700 which on my snap on solus pro isnt documented is this crash data?

Much thanks in advance.

**juozas10** · 1st April, 2010, 07:45 PM

Originally Posted by obdmaster

A friend has just bought an accident damaged 2007 ford galaxy, which hes repaired and replaced both seat belt pretensioners, airbag light is on with code U1A3700 which on my snap on solus pro isnt documented is this crash data?

Much thanks in advance.

Hi.
It is crash data.
Please read dump, and sent here.
Best Regards.

**obdmaster** · 1st April, 2010, 08:09 PM

Originally Posted by juozas10

Hi.
It is crash data.
Please read dump, and sent here.
Best Regards.

Nice one juozas10, will post dump when ecu is off vehicle ,thanks m8

**modulegod** · 1st April, 2010, 11:09 PM

hi mate, you can reset all late ford modules in the car with an ids vcm dealer interface loads of diagnostic guys have them. you read the fault codes in airbag then highlight the crash code which will have a description saying lateral acceleration sensor threshold exceeded crash detected. then click the button to do a pin point test and the software will ask if you would like to erase the crash data.... click yes job done.

not all people with vcm ford scanners know this can be done and even guys i know that work for fords dont know.

hopefully u know someone with a vcm or can find someone.

i do loads of late ford modules via the epprom but unless you have a tested file taken from a non crashed module its near immposible to spot the crash data its not in blocks like most files its hidden away.

hope this helps.

**obdmaster** · 2nd April, 2010, 11:24 AM

Originally Posted by juozas10

Hi.
It is crash data.
Please read dump, and sent here.
Best Regards.

Here you go my dump of 95160, part no .of unit 0 285 010 140 .

Thanks for this my m8.

**juozas10** · 2nd April, 2010, 12:14 PM

Originally Posted by obdmaster

Here you go my dump of 95160, part no .of unit 0 285 010 140 .

Thanks for this my m8.

Hi.
Please write full airbag ECU discription.
Try this...
The last foults are NECESSARY clearing by diagnostic. Write back if it works.
Password is in your PM
Best Regards.

**obdmaster** · 2nd April, 2010, 01:11 PM

Originally Posted by juozas10

Hi.
Please write full airbag ECU discription.
Try this...
The last foults are NECESSARY clearing by diagnostic. Write back if it works.
Password is in your PM
Best Regards.

Yes juozas10 it worked great, had to clear code as you said m8, thanks 300%. Your a TOP man m8. cheers m8

**juozas10** · 2nd April, 2010, 01:30 PM

Originally Posted by obdmaster

Yes juozas10 it worked great, had to clear code as you said m8, thanks 300%. Your a TOP man m8. cheers m8

Please write full airbag ECU discription
Thanks for your reply.
Best Regards.

**Andywill** · 27th April, 2011, 06:34 PM

Hi, I have similar, 2007 Galaxy with a no start complaint, customer reports never started since accident. No dtcs logged in engine controller, but found dtc logged in airbag U1A37 CRASH STATUS TELEGRAM, suspect the airbag is canceling the engine running function - or perhaps has nothing to do with no start issue. Has anyone come across this with late Fords.