Need Orange5 in-circuit wiring diagram for XC2361A-56(2013 Land Rover)

**Tronics** · 27th April, 2021, 08:03 PM

Hello guys,
I need orange5 in-circuit wiring diagram for XC2361A-56 mcu in Airbag module BJ32-14D374-AC (2013 Land Rover). If any of you can help, I will be more than happy.
Also, I noticed that there is no pin for TRST on orange5 programmer. Does orange5 use diifferent abbreviation for TRST?

**Hondasilver** · 27th April, 2021, 11:46 PM

Please post pics of you airbag module circuit board .
I noticed Orange 5 have it label as RST .
Which TRST or RST is also known as Reset.

**Tronics** · 28th April, 2021, 08:18 AM

Originally Posted by Hondasilver

Please post pics of you airbag module circuit board .
I noticed Orange 5 have it label as RST .
Which TRST or RST is also known as Reset.

Hello, Here is the photo of the board attached. Are you sure RST and TRST are the same?
Can you please give me the wiring diagram if you have it.
WhatsApp Image 2021-04-26 at 11.00.41.jpg

**Hondasilver** · 28th April, 2021, 08:47 AM

Hello, yes i am sure RST and TRST and Reset are the same.
Please send the picture of the other side of the module.

**Tronics** · 28th April, 2021, 09:04 AM

Originally Posted by Hondasilver

Hello, yes i am sure RST and TRST and Reset are the same.
Please send the picture of the other side of the module.

Thank you for the info. Here is the other side attached.

otherside.jpg

**Hondasilver** · 28th April, 2021, 11:56 PM

Here is two pinout diagram i found . They both looks like the same in regards to connection points for programmer.
So here are the conversion from Orange5 to the pinout below.

Orange 5 Pinout diagram below

GND GROUND
RXD TDI ( GREY)
TXD TDO ( ORANGE)
RST RESET (WHITE)
OSC TCK ( BLACK)
PDX TMS ( YELLOW)
VCC TO 5 volt ( NOT NEEDED FOR THIS MODULE)

Please press Thanks and Reputation if i was helpful to you.GJ23-14D374-AB JTAG.jpg Landrover_Autoliv_DK62-14D374-AG_XC2361A-56F_JTAG.jpg

**Tronics** · 29th April, 2021, 05:37 AM

Originally Posted by Hondasilver

Here is two pinout diagram i found . They both looks like the same in regards to connection points for programmer.
So here are the conversion from Orange5 to the pinout below.

Orange 5 Pinout diagram below

GND GROUND
RXD TDI ( GREY)
TXD TDO ( ORANGE)
RST RESET (WHITE)
OSC ---------
PDX TMS ( YELLOW)
VCC TO 5 volt ( NOT NEEDED FOR THIS MODULE)

Please press Thanks and Reputation if i was helpful to you.GJ23-14D374-AB JTAG.jpg Landrover_Autoliv_DK62-14D374-AG_XC2361A-56F_JTAG.jpg

Thank you very very much for your effort for help. I will try it now and report back.

regards

**Tronics** · 29th April, 2021, 05:47 AM

Originally Posted by Hondasilver

Here is two pinout diagram i found . They both looks like the same in regards to connection points for programmer.
So here are the conversion from Orange5 to the pinout below.

Orange 5 Pinout diagram below

GND GROUND
RXD TDI ( GREY)
TXD TDO ( ORANGE)
RST RESET (WHITE)
OSC ---------
PDX TMS ( YELLOW)
VCC TO 5 volt ( NOT NEEDED FOR THIS MODULE)

Please press Thanks and Reputation if i was helpful to you.GJ23-14D374-AB JTAG.jpg Landrover_Autoliv_DK62-14D374-AG_XC2361A-56F_JTAG.jpg

Also, there is TCK point in your photo. What does TCK (in your photo) refer to in orange5?

**Hondasilver** · 29th April, 2021, 07:51 AM

You're welcome my friend.
I just figure out what TCK means in refer to Orange5.
TCK mean OSC in Orange5
i JUST UPDATE THE CONVERSION LIST.
I know with my Xprog , it was confusing too .
But I managed to cross reference some other diagrams like from CPT etc.

**Tronics** · 29th April, 2021, 02:13 PM

Originally Posted by Hondasilver

You're welcome my friend.
I just figure out what TCK means in refer to Orange5.
TCK mean OSC in Orange5
i JUST UPDATE THE CONVERSION LIST.
I know with my Xprog , it was confusing too .
But I managed to cross reference some other diagrams like from CPT etc.

I tried, but it does not even ‘boot’.

**Hondasilver** · 29th April, 2021, 02:26 PM

Did you apply 12 volt supply? , like in the diagram.

**Tronics** · 29th April, 2021, 02:33 PM

Originally Posted by Hondasilver

Did you apply 12 volt supply? , like in the diagram.

Yes, +12 and grnd are externally connected from power supply.

**Hondasilver** · 29th April, 2021, 04:18 PM

Ok , maybe re-check the soldering for the pinsout.
Also check the settings in the software.
Check usb port settings
Did you ever used this programmer before?

**slick_dick** · 29th April, 2021, 04:49 PM

The diagram provided are wrong .. you will end up bricking the ecu!!!

short ground to the board in 2 places

log1 needs connecting and lift up pins 60&62 from mcu

br

slick

**Tronics** · 29th April, 2021, 05:01 PM

Originally Posted by slick_dick

The diagram provided are wrong .. you will end up bricking the ecu!!!

short ground to the board in 2 places

log1 needs connecting and lift up pins 60&62 from mcu

br

slick

Hello Slick,
Thank you for the warning. When it did not even boot, I new something was wrong. Do you have the correct pinout or wiring diagram?
Which one is Log1?

Regards