sat chip is not working, cable is plz help

**zizobouta** · 27th April, 2010, 02:26 PM

hi ya all , i have an open media with 4.60 image for sat tried yesterday to load an image manually then it said erase flash and write and now it wont work. it stays on green light button without turning off with remote. but when i change to cable from behind all is working. so did i damage sat internal chip, does it need jtag or just flash with dreamup? plz
thanks in advance

**cgscott** · 27th April, 2010, 02:28 PM

Flash again with dreamup.

**zizobouta** · 27th April, 2010, 04:36 PM

hi sgscott, i did flash yesterday with dreamup tried once only then i went to bed. the box didnt reply to dream up like no conection. first it said connection is ready plz turn box on i did then nothing happened. is there another way to flash it>? i have to try again

**Bulld0g** · 27th April, 2010, 04:48 PM

If you've only tried it once then try it again m8

**zizobouta** · 27th April, 2010, 04:54 PM

will do that when i get hm. hope i tll work if not then jtag i think

**zizobouta** · 28th April, 2010, 02:25 PM

i ve done it. i managed to flash it with edg nemssis einstein solution but astra 19 has got only 3 transponders/frequencies. is it cos image is old or how do i load all satellite transponders?

**EAMO 2** · 3rd May, 2010, 08:18 AM

Originally Posted by zizobouta

i ve done it. i managed to flash it with edg nemssis einstein solution but astra 19 has got only 3 transponders/frequencies. is it cos image is old or how do i load all satellite transponders?

Check your signal strength, your dish may need to be re-alligned.
Also check all cable connections are sound.
When signal strength is good, re-scan ASTRA 19.
Other option is to flash box using D.K.1.1 or PLI-JADE images.
Both these images are safe to use on cloned boxes.
Always remember Open Media is a DM-500 clone, & some images
will freeze it. Thank God for Dream-Up.
D.K.1.1 is very user friendly image, easier navigation etc.
Pli-Jade 500 has better on-line downloads for downloading cams
etc.
Have fun

**samanh** · 24th October, 2010, 05:40 PM

Hello, I have same problem as above, my cable side of Open Media is working fine, but sat side not. I am not able to flash it with dream up. No comminication with serial bus. Only the green led is on, no reaction to remote control. Can any one help me, please ?
Also, I found one blowed cap. on main board and replaced it, but no improement.

What is flash "edg nemssis einstein solution", mentioned above.
Will continue to try. Thank you for any idea.

**EAMO 2** · 24th October, 2010, 07:13 PM

Originally Posted by samanh

Hello, I have same problem as above, my cable side of Open Media is working fine, but sat side not. I am not able to flash it with dream up. No comminication with serial bus. Only the green led is on, no reaction to remote control. Can any one help me, please ?
Also, I found one blowed cap. on main board and replaced it, but no improement.

What is flash "edg nemssis einstein solution", mentioned above.
Will continue to try. Thank you for any idea.

Use a PC with serial-port when using dream-up. USB-serial leads
are problematic with dream-up. Make sure not to power-on box
until prompted by dream-up. If no joy try older version of dream-up. Have never used einstein solution, but you could google it.
I would exhaust options mentioned above first.

**samanh** · 24th October, 2010, 07:16 PM

Thank you, I am using real com port from old notebook. It is working fine on cable side, but not on sat side. My dreamup version is V1.3.3.2. No success till now. I am trying..

**samanh** · 25th October, 2010, 11:44 PM

Hello, does anybody know, how to properly jtag openmedia box
from sat side? I am going to try soon description find at download section for dreambox. Hope it will help me. Any advice is welcome, as dreamup does not work for me at all.