upa help

**ionut_mtb** · 27th September, 2010, 09:17 AM

hello. i have a problem with the upa usb programmer. i try to read an mc9sdg128e but no success. vdd/vcc out of range, 1 error found device mc....., at connection pin 9 vdd 11.42v Bad. The upa is recognized by the software. the connections are made like in pdf. strange is that one week ago i was reading an mcu with success, and after a day tring the same mcu with same connections and soldering and fail reading... same problem pin 9 vdd Bad..

thanks

**racetu** · 27th September, 2010, 11:11 AM

Give a connection photo

**newgeniehex** · 27th September, 2010, 12:19 PM

Originally Posted by ionut_mtb

hello. i have a problem with the upa usb programmer. i try to read an mc9sdg128e but no success. vdd/vcc out of range, 1 error found device mc....., at connection pin 9 vdd 11.42v Bad. The upa is recognized by the software. the connections are made like in pdf. strange is that one week ago i was reading an mcu with success, and after a day tring the same mcu with same connections and soldering and fail reading... same problem pin 9 vdd Bad..

thanks

HELLO
that is this ,it is a dasboard?cas?or other
maybe it is securised!!!

**ionut_mtb** · 27th September, 2010, 03:01 PM

i had used the connections like in uuprog pdf, with p9 lifted, also tried with pin6 lifted but no success, 2 different cables, and i verrified with multimeter the connections... problem i think it is with the programmer...

**ionut_mtb** · 27th September, 2010, 03:02 PM

this is an airbag module..

**newgeniehex** · 27th September, 2010, 08:15 PM

Originally Posted by ionut_mtb

this is an airbag module..

hello
it is original upa or clone
try to read the simple eeprom

**lamfame** · 27th September, 2010, 10:33 PM

Hello can anybody give connection pdf how to read eeprom of10v of golf3 with upa-usb

**squirrelbandy** · 27th September, 2010, 10:46 PM

i think this is common problem , i have quite a few programmers and my upa ig genuine but i find it hard using it as the settings for each chip are so different . ive managed to read tms and hco5 ok but anything else i dont bother as cant seem to get settings right , maybe there is something somebody can share to show connection settings and i dont mean the pin settings that i already have. i mean what voltage setting for that chip ect ect.

**Smac_a** · 28th September, 2010, 07:10 AM

Hi all,

Are you runnig airbag module on power supply? "Pin 9 vdd 11.42v Bad" - the voltage is way too high as upa can only deliver 5 volts (usb). It's also too high for motorola...

Hope it helps,
Smac_a

**rj22** · 28th September, 2010, 08:03 AM

The AIR 0 285 001 249 is CR16

**ionut_mtb** · 28th September, 2010, 09:32 AM

i'm using only the usb voltage, and if i power upa separatly i have almost same voltage..on P9

**ionut_mtb** · 28th September, 2010, 09:34 AM

@newgeniehex

i dont know if it is a clone, what eprom you say i must read? the airbag module has procesor, not eprom...

**Smac_a** · 28th September, 2010, 09:48 AM

Can you post some pictures (will be a lot easier). Although if there is motorola on pcb there is a good chance that dump you are looking for is stored there...