updating Duplicate SBB fault

[ahmadalbeik]

hi
i have try to update the Silca sbb device which in not original made
it work for me for three times only
and after that when i turn it on it show a white screen
and doesn't load the software
is there is any way to fix this problem
???????????

[kody_2004]

Hello!! ahmadalbeik
You need program U3 and U4 (MX29F016_Tsop48)
and program then 24cs16 to solve this,in atach then
files and not forget to lock eprom 24cs16 lift pin 7 and
link to pin 8.
Later you can update this for vers_32.2

Regards....

[Meat-Head]

Hello!! ahmadalbeik
You need program U3 and U4 (MX29F016_Tsop48)
and program then 24cs16 to solve this,in atach then
files and not forget to lock eprom 24cs16 lift pin 7 and
link to pin 8.
Later you can update this for vers_32.2

Regards....

cool.

Is this dump no tokens? Or does it need tokens?

[ahmadalbeik]

Hello!! ahmadalbeik
You need program U3 and U4 (MX29F016_Tsop48)
and program then 24cs16 to solve this,in atach then
files and not forget to lock eprom 24cs16 lift pin 7 and
link to pin 8.
Later you can update this for vers_32.2

Regards....

thanks alot
i will try it and post the result
but could you let me know what device you use to read MX29F016_Tsop48

[kody_2004]

Hi!!
For Meat-Head:This dumps have 0 tokens but in most cars work ok.

For ahmadalbeik: i use a elnec programmer with a zif socket
adapter dil to tsop 48,but you can use a cheap programmer
like Willem-Eprom ( h**p://www.sivava.com/) with adapter or any other for program flashs.

Regards...

[Meat-Head]

do you know where in the dump and which ones the tokens are stored?

Would be cool to 'load up' 500 tokens.

Great when out down town with mates - 500 tokens

How do you unsolder the chips? hotair?

Thnaks

What other stuff you got?

[kody_2004]

I disassembled then firmware and trying understand this
yes hot air,but be carful to not damage then board if not have experience better practice in old boards.

[canorivera]

I disassembled then firmware and trying understand this
yes hot air,but be carful to not damage then board if not have experience better practice in old boards.

Hi, can a v29 be updated to this firmware??

Chinese say that is different hardware...

Any help about updating T300???

Thanks...

[kody_2004]

Hi!!canorivera
Can you put here details pictures inside of v29.

[Meat-Head]

Hi, can a v29 be updated to this firmware??

Chinese say that is different hardware...

Thanks...

Pop your botom off and have a poke around.

Having difficulty getting my bottom off - dam chinese screws.

*IF* ever get damm epprom programmer sorted, just going to change 24c16 eeprom file - close eyes and press update

might even change serial number to match one on the back or to say 'MEAT-HEAD-MOTORS'

[canorivera]

Yes here it is...

[Meat-Head]

i'm looking forward to seeing the MAX RS232 chip.

Good photo, nice red rings

[v8 dave]

*IF* ever get damm epprom programmer sorted, just going to change 24c16 eeprom file - close eyes and press update

Willem Enhanced - has on board TSOP ZIF socket. Used to use it for flashing other things

Saw them on eBay going for 30 notes recently.

[Meat-Head]

Funny you should say that, just been looking at them

Can it be used for flashing at Tracy Barlow?

Adaptor is about 60 quis i think.

Nice to know if can be read/write incircuit.

Off to bed - knackerd.

[v8 dave]

Alas not, it can only flash at Holly Willoughbooby, but that's good enough for my needs.

I looked at TSOP ICP test clips, but thought eff that when I saw the price (~600 quid). PLCC32 and PLCC44 clips would be good though.

Can't do 93cx6, but 5 quid programmer and soic clip sorted that