Hi all,
Interface correct connect PC.No communication cars.Not working relay and no power PIC16F684, relay etc..
Need dump flash W25x80AV.
THX
Hi all,
Interface correct connect PC.No communication cars.Not working relay and no power PIC16F684, relay etc..
Need dump flash W25x80AV.
THX
Col19 (24th January, 2020)
1.if there is no power in PIC, check Q4.
2.if there is no +5 V, check LM2674(U5) and diodes D3,D4.
Bin dump to my board
Procesor M90F
PIC16F684 + fuses /fuses only hex/
Flash 25x80AV /25X40AV/
Foto fuses for Asix Presto programmer
OBD and Interface wiring /autor DITEX/
any ideas....
thx friends.
ANYd.
Adi202 (2nd April, 2023), AlexDi (15th March, 2023), Anatolijus (18th May, 2018), brodaty (3rd November, 2016), carpin (10th September, 2018), Cinek75 (7th March, 2016), Col19 (24th January, 2020), Dalautos (10th April, 2019), darkwooddark (7th April, 2021), flashs (19th May, 2023), fluorescent (30th June, 2016), gkanev (12th April, 2023), hbalazs (22nd March, 2016), hedi makhlouf (2nd February, 2017), hmagga (26th September, 2022), johny2h (16th June, 2016), kral06060 (14th July, 2017), kronk92 (9th November, 2016), mcb58 (2nd December, 2017), mexanico1971 (19th March, 2015), miltas (21st February, 2018), nikiver4ov (22nd September, 2020), okm (6th February, 2018), rrr500 (4th July, 2018), shtyrya2 (26th September, 2022), thunderwinged 2 (5th June, 2020), titoun (18th February, 2016), varoff (31st January, 2017), Ximot (1st May, 2023)
And fuses for Asix Presto...
carpin (10th September, 2018), Cinek75 (7th March, 2016), Col19 (24th January, 2020), Dalautos (10th April, 2019), darkwooddark (7th April, 2021), gkanev (12th April, 2023), nikiver4ov (22nd September, 2020), okm (6th February, 2018)
Col19 (20th June, 2021), Dalautos (10th April, 2019), Elektrik001 (15th April, 2015), frigo (16th August, 2013), johny2h (16th June, 2016), kral06060 (14th July, 2017), nikiver4ov (22nd September, 2020), shtyrya2 (26th September, 2022)
To post # 7
What transistors have to be:
n-channel or p-channel
T3 (4pin PIC) = 352A4 - p-channel ? (datasheet 352AP)
T5 (1pin PIC) = 352A4 - p-channel ?
T6 = Y2. - p-channel
7002 - n-channel
Thank you in advance for your answer.
-------------------
Replaced 3 transistors (T3, T5, T6) for p-channel. The voltage (PIC) at pin1-5V, pin4-12V.
Relays still do not work.
Help!.
Last edited by Stanicek; 25th June, 2016 at 09:03 PM.
thanks Anydraj very useful
Thanks a lot!!!!
Thanks.I look.RAM removed, It did not help.
Transistor 2N2007 or 2N7002 ?
Last edited by Anydraj; 18th November, 2010 at 07:24 AM.
Hi friends!I had version 22.95 and everything was fine .. after I installed the 24.01 version, can not communicate with the car and get the following message:''comunication error''!I mention that use this interface for 3 years and I did update the internet every time without problems.This worked well one day then did update and died.Any idea?Interface corect conect with pc but not comunicate with car!
tell me please on the reverse side of the Board with fujitsu part all tranzistor 2n7002?
Last edited by KNS1; 6th February, 2016 at 07:55 PM.
Bookmarks