Anyone have the service info on cdi injector R&R? Thanks
Results 1 to 10 of 10
-
31st January, 2011, 08:33 PM #1Banned
- Join Date
- Feb 2010
- Posts
- 59
- Thanks
- 4
- Thanks
- 1
- Thanked in
- 1 Post
Sprinter CDI injector replacement tech info
-
31st January, 2011, 10:38 PM #2DK Veteran
- Join Date
- Dec 2009
- Location
- London Middlesex
- Posts
- 1,264
- Thanks
- 128
- Thanks
- 48
- Thanked in
- 33 Posts
What you need to know mate?
Apart from the pull it out grief it's all pretty straight forward..
Intakes out, cover out etc...fit new washers and clamp bolts and off it goes.Whatever seems impossible is just not yet important enough.
-
31st January, 2011, 10:50 PM #3Junior Member
- Join Date
- Mar 2010
- Location
- Liverpool
- Posts
- 33
- Thanks
- 0
- Thanks
- 0
- Thanked in
- 0 Posts
Depending on the year you may find that the lining of the top cover has melted, if so it will be all over the injectors and the allen bolts securing them. When this happens it will put hours on the job. If I remember correctly tighten sequence for clamp bolts is 7nm plus 90 degrees. Hopefully you wont have the problem with cover, good luck.
Originally Posted by talmadge
Its not what's in your toolbox, its whats in your brainbox that counts.
-
31st January, 2011, 10:57 PM #4DK Veteran
- Join Date
- Dec 2009
- Location
- London Middlesex
- Posts
- 1,264
- Thanks
- 128
- Thanks
- 48
- Thanked in
- 33 Posts
Originally Posted by nutsman
It's not the cover melted but carbon build from leaking injectors mate. Either way you'll need a tool to clean injector seat in head.Whatever seems impossible is just not yet important enough.
-
1st February, 2011, 10:26 PM #5Banned
- Join Date
- Feb 2010
- Posts
- 59
- Thanks
- 4
- Thanks
- 1
- Thanked in
- 1 Post
Yea it took about 2hrs with a pick and pb blaster to get all the black carbon out, but injectors wont move ,scared I am going to break some think, I have ordered a tool from Hutson Precision.I was not sure I was doing it right. But after a little reading up Its called black death, its blow by and diesel.I guess a simple job is never simple.
-
1st February, 2011, 10:28 PM #6DK Veteran
- Join Date
- Dec 2009
- Location
- London Middlesex
- Posts
- 1,264
- Thanks
- 128
- Thanks
- 48
- Thanked in
- 33 Posts
Not on a CDI Merc mate Originally Posted by talmadge
Last edited by florinyes; 1st February, 2011 at 10:41 PM.
Whatever seems impossible is just not yet important enough.
-
1st February, 2011, 10:38 PM #7Banned
- Join Date
- Feb 2010
- Posts
- 59
- Thanks
- 4
- Thanks
- 1
- Thanked in
- 1 Post
Not on a CDI Merc mate.. What ??
-
1st February, 2011, 10:42 PM #8DK Veteran
- Join Date
- Dec 2009
- Location
- London Middlesex
- Posts
- 1,264
- Thanks
- 128
- Thanks
- 48
- Thanked in
- 33 Posts
Previous post edited..
Whatever seems impossible is just not yet important enough.
-
5th February, 2011, 08:18 AM #9Member
- Join Date
- Jun 2010
- Posts
- 66
- Thanks
- 1
- Thanks
- 1
- Thanked in
- 1 Post
By the sounds of it you will need a good puller and seat cutter. Some can be stuck pretty well. You may even break the cam cover.
Good luck.
Andy
-
16th February, 2011, 01:04 AM #10Banned
- Join Date
- Feb 2010
- Posts
- 59
- Thanks
- 4
- Thanks
- 1
- Thanked in
- 1 Post
Update :Tried to pry them out
Tried to use a vice grips and wiggle them out soaked them for 24 hrs and used a slide hammer ordered a puller and cutter from hutson-precision-components 
like cutting butter, the only problem I ran in to after that, was one of the little I mean VERY VERY LITTLE steel balls dropped on the floor and went in to frairy tale land, had to buy one injector
Reply With Quote
Bookmarks