PW please
is it read from xprogm updated to 5.3 and registred?
PW please
is it read from xprogm updated to 5.3 and registred?
Thank you for your efforts to get the firmware xprog-m.
Of course this takes time and costs a lot.
Just a note unlock cost MCU ATMega not cheap, it costs around USD 600-1000.
We must understand the principles that he applied in this DK forum....
Last edited by bram380; 6th June, 2011 at 02:50 AM. Reason: time out
[I]Automotive Electronics Solutions
Mercedes-Benz Reverse Development Engineer ...
Mercedes CFF 2010-2017 CFF all models all modules
Vediamo help flashing over teamviewer ...
JLR SDD online + offline ...last official ...
Your update Bram380 work perfect.
Thank's mate for that.
[I]Automotive Electronics Solutions
Mercedes-Benz Reverse Development Engineer ...
Mercedes CFF 2010-2017 CFF all models all modules
Vediamo help flashing over teamviewer ...
JLR SDD online + offline ...last official ...
could someone upload 5.3 please as i'd like to update but having problems downloading from the net.
I know that but who make big mistake to make upgrade to 5.3 and get shit and was downloaded FW on time ;-)
Can easy make working XprogM.
Or who dont like as is then better buy new tool or pay unlocking tool ....
I was give for free and I hope to someone find way to make Micronas also...
Regard's
[I]Automotive Electronics Solutions
Mercedes-Benz Reverse Development Engineer ...
Mercedes CFF 2010-2017 CFF all models all modules
Vediamo help flashing over teamviewer ...
JLR SDD online + offline ...last official ...
I think eeprom part must be edited a little.
I didn't "downgrade" my xprog-m yet, because when looking at eeprom part I was almost sure micronas are not authorized.
(I'll explain more when I come home this afternoon.)
It is nice to see I push some peoples FORWARD with XprogM.
Maybe we soon have HOMEMADE XprogM.
And for all who want something and not give same to other they must wait some better day's.
I dont see same thing from others isn't it ?
If I will see similar post I will back full no pass protected file but I expect also for all as something like that.
I can see 1000... dump's project's which is 10$ tool's ...
No one give simmilar ( maybe a couple of peoples is true ).
Regard's
Last edited by elchip; 6th June, 2011 at 01:37 PM.
[I]Automotive Electronics Solutions
Mercedes-Benz Reverse Development Engineer ...
Mercedes CFF 2010-2017 CFF all models all modules
Vediamo help flashing over teamviewer ...
JLR SDD online + offline ...last official ...
Here is my idea about authorizations:
Attached screenshot shows extracted eeprom part of "elchips" firmware file. (sorry, elprog, I have to put a screenshot here, I can't explain without the picture).
Looking at the marked part, you'll see it consists of 5AA5 and A55A blocks. Now look at the authorizations screen of our xprog-m programmer. In case of full authorizations, we'll have total of 22 lines, 9th line is "Development tools" and shows "-" instead of "authorized". ARM micronas are two last lines, which are not authorized in our case.
Now look again at our screenshot - let's make a presumption that 5AA5 means "authorized", and A55A means "not authorized" or "-".
That idea works perfect for first 15 lines - we have 8 authorized lines, one not authorized and then 6 authorized.
Now comes a little messy part: 11 A55A's, 3 5AA5's, 1 A55A, 2 5AA5's and finally 8 A55A's.
Counting in total, we have 19 "authorized" lines (what is good), and we need 21 to make ARM micronas authorized, too.
According to that logic, two of eight A55A's in last "unauthorized" block must be changed to 5AA5 to become "authorized".
Maybe I'm totally wrong, but somehow it seems to me this could work. Because I repaired my xprog-m programmer in other way, and now works 100%, I would like someone (Bram380 maybe?) to test my idea.
Of course, I don't know will this work at all, what about checksums etc. - it's only an idea...
mexanico1971 (4th September, 2016)
perfect,if it work like you say
your are the best;my freind
Bookmarks