Hi
Try this and post results .Pass is in your pm .
regards
hi friends
i have crashed airbag control unit for Peugeot 207 year of product 2011 ( this control unit with plastic cover and metal base )
i need your help clearing crash data for this unit
Peugeot 207 2011
Peugeot part No. 96 750 6880 80
Bosch Part No. 0 285 010 828
eeprom ST95160
i attached the eeprom file
regards
Hi
Try this and post results .Pass is in your pm .
regards
DAVID8HENRY8 (7th December, 2016)
DAVID8HENRY8 (7th December, 2016)
Hi
It must be ok . Test it .
here is worked 100% clear, i tested 1000x
pass in PM
Cheero
CHEERO
++++ GOOD WORK ? + ++++
FIAT EMEA 7inch, Ford Sanyo, DELPHI Chrysler Jeep Dodge, DELPHI Volvo GMC Renault, Ford FIC, Fiat Turkey, Ford V Series Calc, Fiat Continental VP1 VP2 Calc, Opel Delco CDR500 & CDR2005 Calc, Mercedes Alpine Calc, Jaguar Alpine Calc, Fiat Daiichi Calc, Delphi Famar Fueguina Calc, Renault Calc, Dacia Calc, Grundig oldtimer Calc, Chrysler Jeep Dodge Panasonic Harman Becker Alpine Continental Calc, Blaupunkt Calc, Philips oldtimer Calc, Audi Aisin RNS-E Calc ....
CarProg020 (8th June, 2015), larsen (31st July, 2013), lorexx (31st March, 2015)
to my friend antlio
after i program the chip with your file no communication with airbag ecu thanks for you help
thank you friend cheero for your help i compared your file with the file that i have from antlio and they are the same are you sure that the file is 100% ok ?
i tested the power lines and the ground and communication lines and they was ok ( i connected the power small connector with an older ecu and there was good communication with the scanner)
i still need your help my friends
regards and big thanks to all of my friends
Last edited by naelraddad; 19th June, 2011 at 08:57 PM.
Hi
Write again the crash file in the ecu and see if you
have communication with tester or not . If you don t
have then the problem is in your car . Anyway my solution had work in the past many times in different ecus like yours .
My friends antlio and Cheero thank you a lot for your help your files are the same and both are working 100% till now I did not understand what happened with me and what was wrong I program the control unit with antlio file and there was no communication I programmed the control unit with the file from cheero and everything was ok ( I am sure the your tow files are the same )
i am so sorry for my mistake in work.
really thanks
big regards to all of my friends
I have same airbag for repair,if possiblle to get pass for dump?
I have in carprog but not same number (745),ecu must be send far so can't test here.
Tanks in advance.
Here dump,sorry
here is dump for your ecu, tested and work 100%
pass in PM
best regards
Cheero
CHEERO
++++ GOOD WORK ? + ++++
FIAT EMEA 7inch, Ford Sanyo, DELPHI Chrysler Jeep Dodge, DELPHI Volvo GMC Renault, Ford FIC, Fiat Turkey, Ford V Series Calc, Fiat Continental VP1 VP2 Calc, Opel Delco CDR500 & CDR2005 Calc, Mercedes Alpine Calc, Jaguar Alpine Calc, Fiat Daiichi Calc, Delphi Famar Fueguina Calc, Renault Calc, Dacia Calc, Grundig oldtimer Calc, Chrysler Jeep Dodge Panasonic Harman Becker Alpine Continental Calc, Blaupunkt Calc, Philips oldtimer Calc, Audi Aisin RNS-E Calc ....
Tanks a lot pal.
hi
i have the same problem with this airbag sensor. its possible help-me ?
many thanks
regards
here is 100% working clear
best regards
Cheero
www.cheero.cz
++++ GOOD WORK ? + ++++
FIAT EMEA 7inch, Ford Sanyo, DELPHI Chrysler Jeep Dodge, DELPHI Volvo GMC Renault, Ford FIC, Fiat Turkey, Ford V Series Calc, Fiat Continental VP1 VP2 Calc, Opel Delco CDR500 & CDR2005 Calc, Mercedes Alpine Calc, Jaguar Alpine Calc, Fiat Daiichi Calc, Delphi Famar Fueguina Calc, Renault Calc, Dacia Calc, Grundig oldtimer Calc, Chrysler Jeep Dodge Panasonic Harman Becker Alpine Continental Calc, Blaupunkt Calc, Philips oldtimer Calc, Audi Aisin RNS-E Calc ....
Bookmarks