X prog m and atmega 64

**ecufix** · 17th October, 2011, 06:28 PM

Has anybody successfully used a Xprog m to read and write to atmega 64 ? The only " live" buttons I get are blank and erase .
please advise me if there is a procedure , just purchased a new atmega for my cloned x prog m and want to load it with the
firmware received from a fellow DK member . thanks guys

**ecufix** · 19th March, 2012, 02:14 PM

After many months of battling with this one I eventually got it right . Xprog m's connecting diagram is WRONG .B0 must go to pin #2 and B1 to pin#3 on micro , repairs and upgrades here we come , regards

**vanos batam** · 19th March, 2012, 02:59 PM

here your full dump from good X prog m

**vanos batam** · 19th March, 2012, 03:00 PM

here the schematic diagram

**ecufix** · 19th March, 2012, 03:18 PM

Thanks Vanos for the pic version of x prog . My post is about the atmega 64 version , I blew the micro doing something silly and after buying a new micro i could not program it , until i saw this error as posted above ,regards

**Holtek** · 19th March, 2012, 11:51 PM

Set everything as the screen:

**georgegt** · 26th March, 2012, 10:32 PM

Where can I find a good dump for atmega 64 ?

**kestuxs11** · 28th March, 2012, 10:20 PM

thanks for schematic, my xprog-m is broken and I'll try to repair...

**mtnt** · 3rd April, 2012, 01:12 PM

Hi Friends
Couple days ago i upgrade my xprog to to xprog box and probably You know what i have now..
May some one help me... I need to know how to read ATm64 buy UPA... I see on pcb pin but when I tray UPA it doesn't see ATm
I check pin on pcb to pin on 64 plcc but... upa had problem Could someone show how to connect ( which pin on pcb connect)
Regards!

ok now i read this AT but I see only 00000000000000000000000 in all flash.... what I did wrong___HELP

**ahadi** · 3rd April, 2012, 03:17 PM

Originally Posted by mtnt

Hi Friends
Couple days ago i upgrade my xprog to to xprog box and probably You know what i have now..
May some one help me... I need to know how to read ATm64 buy UPA... I see on pcb pin but when I tray UPA it doesn't see ATm
I check pin on pcb to pin on 64 plcc but... upa had problem Could someone show how to connect ( which pin on pcb connect)
Regards!

ok now i read this AT but I see only 00000000000000000000000 in all flash.... what I did wrong___HELP

maybe you couldnt read you could write.

**micromax** · 7th April, 2012, 11:33 AM

if you want read or write atmega by xprog you must create project by menu, next select file for flash, eeprom and config.

**mtnt** · 11th April, 2012, 06:49 PM

no i use upa
and i dont know how to connect which pins
6 pins Vcc-52 GND-53 reset -20 msio-13 mosi-12 sck-11???????????????
it's good ???
Friends i need help my upa read only "0" and program the same "0":/

**tatop** · 27th April, 2012, 11:01 PM

Originally Posted by mtnt

no i use upa
and i dont know how to connect which pins
6 pins Vcc-52 GND-53 reset -20 msio-13 mosi-12 sck-11???????????????
it's good ???
Friends i need help my upa read only "0" and program the same "0":/

i have egual problem
sigh sigh