Thanks!!! i really needed it
Thanks!!! i really needed it
i been looking for the vag revival for a long time thanks
IMG_0512.JPGIMG_0513.JPG
I have interface for VCDS like on picture
ver 11.11
but not work
led flashing red, when conect to car its green, but sw not see cable
VID 0403 PID FA24
on interface missing 7805, atmega is on usb power, and no GAL chip
wich version to update on this cable to work OK?
thanks
Mate
This tool comes with a dedicated VCDS softwear.
If I know well it is v11.11.3
Did you use this one?
And please share pics with the message that you show after you do TEST
and from ABOUT
Maybe you do something wrong and you do not need to reflash the Atmega
BTW this is the worst tool made VCDS made in China I ever seen
Good luck
mladen76 (30th March, 2013)
Everything to cut expence and to improve profit...
I guess price is the same like one that have all chips
My advice-send them back that shit they send you if you have a chance to get money back...
Last edited by mladen76; 30th March, 2013 at 03:43 PM.
yes, I sent back 4 peaces, and pay post, i have refund money, but last week i recive back packet with this cable (becouse wrong adress) then I try to repair.
error.jpg
this is error message from sw 11-11-3
yes, I sent back 4 peaces, and pay post, i have refund money, but last week i recive back packet with this cable (becouse wrong adress) then I try to repair.
error.jpg
this is error message from sw 11-11-3
USB\VID_0403&PID_FA20.DeviceDesc="Ross-Tech HEX or KEY USB Interface"
USB\VID_0403&PID_FA23.DeviceDesc="Ross-Tech Micro-CAN Interface"
USB\VID_0403&PID_FA24.DeviceDesc="Ross-Tech Direct USB Interface"
USB\VID_0403&PID_DF20.DeviceDesc="Ross-Tech USB Converter"
USB\VID_0403&PID_FA30.DeviceDesc="Ross-Tech Direct Interface"
this is part from rt-usb.ini file, I try put all of then, but same problem.
mybe atmega ic clear, ... In first start program, and conect vcds to usb, vcds try to find driver, but driver not find, PID is wrong, I dont know which PID is writen to cable
someone who have flash and ept file, then I try to reprogram. Mybe then work
Last edited by alldecode; 30th March, 2013 at 04:10 PM.
For your interface the VID/PID must be this:
USB\VID_0403&PID_FA30
Use MProg and change the FA24 into FA30
Then must be recognized.
Good luck
why I can not program the fuses and the bit"s ?!
I bean able to erase the AT162 but not write it !
UPA ori say"s that is successfully programmed but is not !
what possible could be ?!
BR
My work is my life ART TECH GARAGE
in one cable give mi this error:
sw is 1.84 and upgrade to 1.91, then upgrade is over, cabal works
vcds 1.91.JPG
now i have 3 peaces, and try to directly flash with 1.84 (11.11) then upgrade, maybe be sucess
Last edited by alldecode; 30th March, 2013 at 10:09 PM.
Mate use the softwear that comes with interface.
That kind of tool that you have it is usually sold with VCDS 11.11.3 softwear.
As I allready told you the VCDS 11.11. it is generic. There's 11.11.0 version, 11.11.1, .....11.11.5
And your tool dump works just one version of VCDS that comes with the interface not with other.
That's why it said "Interface Not Found"
Good luck
alldecode (30th March, 2013)
"mexanico1971"
I programing atmega with pony, and is OK
try to ponyprog, are you have schematic for interface?
mexanico1971 (31st March, 2013)
OK, matty... but if i have newer sw, like 11.11.4 and higer, that sw upgrade interface without directly flash atmega?
No mate
The softwear upgrade just the firmwear in the Atmega.
And this just if you have a not blacklisted serial in the Atmega eeprom
I suppose you have a blacklisted serial so you cannot upgrade it.
If you allready tried this then you need to reflash your tool with a dump and use the version of VCDS for that dump.
Good luck
Bookmarks