VAG-COM/VCDS LATEST DUMPS

**gazvts** · 26th January, 2015, 01:06 PM

dumps for 12.12.0 on the web

**kidloco** · 27th January, 2015, 10:01 PM

Please i need info how to make VCDS 12.10 with FTDI RL to any original VCDS Version example 11.11.0. thank you

**paro44** · 28th January, 2015, 08:45 AM

Look at the big "vcds everything" thread, you can find there the aminebot tutorial for repair.
You can't make an original, since the public serials are blacklisted in software. Software update an internet connection will disable your interface.

**kidloco** · 28th January, 2015, 03:44 PM

Thx, i was lokking there but could not find aminebot tutorial ,, plase can you give me a link or ...

**volk** · 21st April, 2015, 09:08 AM

Hello. I need advice for relfashing atmega vie LPT. I can write eeprom but can't write flash.Witch format do I have use .bin or .hex? Thanks.

**ola98** · 13th August, 2015, 04:38 PM

hello,

is possible to repair china cable vag912 ?

**gopelhu** · 15th September, 2015, 12:53 AM

Hi all,

Here is my solution, ENJOY !!!

config with ponyprog, and installer very big size and i caanot upload it.

if anybody need it pl write me pm.

Regards,

**tehnards** · 14th December, 2015, 12:34 AM

Hi there,

New here, due to a bricked Chinese vag-com interface 11.11 :/

Made a stupid mistake. Looking to see if I can just use vag-com revival to reprogram or if I need to do much more. Sorry, I know these are noob questions.

**Gizimo** · 27th December, 2015, 03:30 PM

Hello, I have a HEX + CAN DUAL-K CAN USB interface.
Unfortunately, I have used a newer VCDS software and it asked me for a FW update from 1.92 to 1.94. Now unfortunately gone Something wrong and he accepts the connection but no longer recognize the interface.
The FTDI FT Prog recognize it perfectly. Can anyone help to liven up the part to me again?

Device Info from FTDI:
Chip Type: FT232R
Vendor ID: 0x0403
Product ID: 0x6001
Product Desc: Ross-Tech
Location ID: 0x11
EEPROM Type: 93C56 EEPROM

Hope it can someone help.

vagscreen.JPG vagscreen2.JPG

**Gizimo** · 27th December, 2015, 07:37 PM

Am I in the right place in the category? Any ideas what is wrong with the cable now?

I would be really grateful for your solutions.

**Gizimo** · 29th December, 2015, 09:54 PM

Is there someone who can help?

Gesendet von meinem C6603 mit Tapatalk

**Gizimo** · 1st January, 2016, 09:10 PM

push

Gesendet von meinem C6603 mit Tapatalk

**tango** · 2nd January, 2016, 04:56 PM

if original software used then your atmega has been wiped
you need to reprogram the interface
look inside interface and see what mcu is there if atmega your ok and can fix but if nec then best buy another

**Gizimo** · 2nd January, 2016, 06:46 PM

Big Thanks Tango, for your Help.
Chip is an
ATMEGA162
16AU
1308H

Gesendet von meinem C6603 mit Tapatalk

**mattydr67** · 4th January, 2016, 01:51 PM

@Gizimo
First of all as I can see in the pics shared by you your tool is sklad66 vcds hq clone.
Secondly its right that it shows you vid/pid 0403/6001
Do not touch it. You will damage it.
Ok you loosed the warranty because you open it.
Now let me know what softwares version for vcds did you used and from where?
That tool is working only with sklad66 cracked software so do not use any other kind of vcds versions craked or not.
Good luck