Digiprog 3 clone questions and answers

[gjenkins0]

check connections on cable , suppliers normally don't get pinouts correct , i usually go online get digi-prog 3 cable pinout and re-solder the cables according to the diagram

[gjenkins0]

My experience with digiprog 3.

mercedes benz obd

w211 30 seconds
w212 pre-facelift 30 seconds (EIS)
w203 face lift 30 sec
w204 pre facelift 30 sec (EIS)
'' '' facelift 30 sec (EIS)

VW GOLF 4,5,6 OK OBD2

MOST TOYOTA OK NO PROBLEM EEPROM
70 percent nissan, not good for navara/pathfinder 9s12, older dash works but certain one kills dash
old ford ranger mcu dash ok solder pins on back


another good tip is to make your own icp cable for digiprog , download cable pinout and make 123458 for in circuit programming works very well.


hope this info can help.

[jjservice]

anyone has a pin out for this LCM3 BMW X5 E53 using digiprog3?
anyone had tried this before?
which connector able to use? does this LCM can do by DIGIPROG3 OBD2?
*the LCM MCU has a motorola ( XC528647CFN4 mask 0H30R)

thanks in advance

X5_.jpgX5__.jpgX5___.jpg

[Joeyfast13]

check connections on cable , suppliers normally don't get pinouts correct , i usually go online get digi-prog 3 cable pinout and re-solder the cables according to the diagram

i did with no luck

[expertinfa]

2012 golf 6 success 2 minutes but had to select up to -2012 and not 2012-onwards

[Haych2011]

Hello Poeple,

Anyone used digiprog 3 on import prius and estima any good?

Also how can I get dumps on it from a pc thanks alot.

Thanks is advance.

Sent from my SM-N976B using Tapatalk

[teerak2uk]

Hello Poeple,

Anyone used digiprog 3 on import prius and estima any good?

Also how can I get dumps on it from a pc thanks alot.

Thanks is advance.

Sent from my SM-N976B using Tapatalk

transfer dumps using eetool

[Haych2011]

transfer dumps using eetool

Is e tool just a software or do I need a physical tool?

Sent from my SM-N976B using Tapatalk

[clusters]

etool is just software, but if your clone does not have the FTDI chip installed (a lot don't) it will not work.

[Haych2011]

OK great i have 2 options before purchasing one one of the options just says normal chip and the other says "Full Set FTDI FT232BL&93C46" im supposing this should be the one also can this adjust mileage for a imported Toyota Estima.


Also thanks alot for the help guys

I'm 18 and new to this guys sorry for the "dummy" questions.

Sent from my SM-N976B using Tapatalk

[MileageAudit5]

2018 infiniti g37 pc386 DON'T DO IT!!!!
I guess this should be obvious but don't do this 2018 g35 g37 car with digiprog. It reads correctly but writes file corrupt. Cluster works just not normally. Cluster goes bad after that. The algorithm is too new for the digi. at least remember to save before reading can probably rewrite if saved? wish I had done that.

[zanel2707]

Hello! Is it possible to do a downgrade from version v4.94 to v4.88 ?I have a Digiprog 3 v4.94 FA9C60160000


Thanks

[teerak2uk]

Hello! Is it possible to do a downgrade from version v4.94 to v4.88 ?I have a Digiprog 3 v4.94 FA9C60160000


Thanks

Possible yes if you have the files.
Why downgrade though?

[zanel2707]

Can’t connect to Dash on my Audi 2012, after a google search I found that only the firmware 4.88 works.
Where can i find/buy the files, any suggestions?

[evss]

there cheap as chips just buy one with 4.88 fitted, without reprogramming the chips inside you cant downgrade