Digiprog 3 clone questions and answers

[satkingno]

Really? What modifications would that be teerak2uk?

[viliukas]

Hi friends, i tried change mileage on mercedes w211, 2007 years (facelift), i choose on digiprog mercedes-w211-tacho diag-plug 16(60)-ok and in the right corner it write that - connection500 - verify 83 and it stopped to work and i got ''ERROR NO COMUNNICATION''. I tried a few times but all the time i got the same...The dash is VDO. With car everything ok - i tried connect with autocom diagnostic tool to dash and other blocks - everything works fine. Where could be a problem? Digiprog 4.94, can works fine on that device(i did a lot can bus VAG cars...). Thanks for your help.

[bodzio012]

Try engine running

[viliukas]

Try engine running

The car was standing about a month, i think starter motor cranked a little bit too slow because battery wasn't fully charged. You think low voltage could be a problem when digiprog try to read the dash?

[Dayo]

Jump start the car. Run for 2 miles. Turn car off. Ignition on and it should work


Sent from my iPhone using Tapatalk

[javyb]

Hi friends, i tried change mileage on mercedes w211, 2007 years (facelift), i choose on digiprog mercedes-w211-tacho diag-plug 16(60)-ok and in the right corner it write that - connection500 - verify 83 and it stopped to work and i got ''ERROR NO COMUNNICATION''. I tried a few times but all the time i got the same...The dash is VDO. With car everything ok - i tried connect with autocom diagnostic tool to dash and other blocks - everything works fine. Where could be a problem? Digiprog 4.94, can works fine on that device(i did a lot can bus VAG cars...). Thanks for your help.

Take dash out and use st60

[viliukas]

Take dash out and use st60

i could try, but the problem is that i have not a full digiprog ( without cable set). Maybe someone could help me with st60 cable pinout? It was a problem for you with this w211 that it couldn't be done throuhgt OBD and helped jus st60 cable for you? I have a friend who has digiprog 4.94 and done this model through OBD over 10 cars...thanks.

[teerak2uk]

i could try, but the problem is that i have not a full digiprog ( without cable set). Maybe someone could help me with st60 cable pinout? It was a problem for you with this w211 that it couldn't be done throuhgt OBD and helped jus st60 cable for you? I have a friend who has digiprog 4.94 and done this model through OBD over 10 cars...thanks.

ST 60

~

~db25 ~ dash
~~

~13 ~~~ ~1 ~GND

~12 ~~~~ 4+6 ~POWER

~9 ~~~~~ 17 ~CAN

~10 ~~~~ 18 ~CAN

[viliukas]

ST 60

~

~db25 ~ dash
~~

~13 ~~~ ~1 ~GND

~12 ~~~~ 4+6 ~POWER

~9 ~~~~~ 17 ~CAN

~10 ~~~~ 18 ~CAN

Thanks mate I'll do this cable and i'll try to do this dash on the table. I have the last question: when i'll do this dash through OBD or on the bench digiprog should show me the old mileage value? Or it will be ''the old value: ?''. thanks.

[memet99600]

Unsolder the chip and try

Hello I try to unsold chip but read wrong mileage and when I push "X" it says unknow version, my digi not work ?IMG_20151026_113420[1].jpgIMG_20151026_113454[1].jpgIMG_20151026_113501[1].jpg

[aem]

are you sure you put pin 1 where it have to be?

[teerak2uk]

Chip looks rotated but could just be poor picture

[aem]

anyway that 35080 can not be write with digi.....only if is new 35080

[PremierD]

......... 35080 in a Merc e class mate ... you need to leave of the weed

[javyb]

......... 35080 in a Merc e class mate ... you need to leave of the weed

There on about a astra h Tam