Carprog Mcu Reflash Step by step

**maciek007** · 8th May, 2018, 09:08 PM

Originally Posted by martom46

znajdowany wsad do carprog wersji v8. 21

https://www.360diag.net/a/downloads/.../1109/397.html

tylko nie mam kodu aktywacji.
może ma jej kalkulator do pomocy?

jeżeli ma ktoś kalkulator lub może policzyć ?
bardzo bym prosił o pomoc

68766-D08B5-BE006-A91EB

Code:

abc

GKYRBZ4YHC5NFXUREUDLHECN5XRXFHLEPZRTRK5PVLTE6DCYQPVFKXPQ9JFR2Y6ZKJ

**sm0k3r** · 18th May, 2018, 10:30 AM

please upload mcu firmware without at88 workng. i test with cp 4.01 without AT88.bin and work. Reason burnt at88

**DjWielebny** · 10th June, 2018, 11:11 PM

Originally Posted by 2m2c

AT91SAM7S256 bin for you

hi I have problem with download dhis attached file can you 2m2c upload again?

**collmen** · 24th June, 2018, 06:07 PM

For sirocco need a1+ adapter

Wysłane z mojego SM-G920F przy użyciu Tapatalka

**Crashburn** · 26th June, 2018, 08:50 AM

Can me anyone say how the steps to Dump a Carprog Flash File?

**Domi** · 26th June, 2018, 09:57 AM

is encrypted

**MrBingo** · 18th October, 2018, 08:18 AM

hello, is it safe to flash the carprog without removing the at88sc? without harm?

**Zann** · 19th October, 2018, 11:23 PM

Originally Posted by MrBingo

hello, is it safe to flash the carprog without removing the at88sc? without harm?

Hello
I have flashed carprog more than 10 times without removing AT88SC and it is still working fine.

**gege974** · 22nd October, 2018, 12:13 AM

Hi
should the wire 55 be resized on the pcb after reprogramming?

**mikroel** · 22nd October, 2018, 12:05 PM

Originally Posted by gege974

Hi
should the wire 55 be resized on the pcb after reprogramming?

Depend of HW version

Sent from my iPhone using Tapatalk

**Zann** · 22nd October, 2018, 08:02 PM

Originally Posted by gege974

Hi
should the wire 55 be resized on the pcb after reprogramming?

According to the datasheet, pin 55 can be left unconnected.

ERASE Pin
The pin ERASE is used to re-initialize the Flash content and some of its NVM bits. It integrates
a permanent pull-down resistor of about 15 kΩ to GND, so that it can be left unconnected for
normal operations.

**gege974** · 23rd October, 2018, 02:29 PM

Hi
thank you for the information

**Mustansar** · 31st October, 2018, 02:24 AM

hi

topic: JTAG programming for Clone Carprog

I have bought CarProg and TL866ii PLus programmer with 10 Adaptors

TL866 Link : https://www.ebay.co.uk/itm/USB-TL866...72.m2749.l2649

and Carprog

https://www.ebay.co.uk/itm/New-VSCAN...72.m2749.l2648

I have searched on JTAG programmer and adaptors but It is very confusing as there are different ones depend on the MCU manufacturer.

I do not have a serial port on my laptop. it is windows 10 with USB ports. Which cable do i need to buy.

Please send a link for item in sale.

Many Thanks!

**Zann** · 31st October, 2018, 06:31 PM

If you want to reflash CarProg you can use J-Link

**jakis28** · 16th November, 2018, 04:56 PM

Hi everyone! After reflashed carprog, I reconnect usb, but nothing happens..PC not found device. When erasing mcu pc found uknown device. Possible couse?