flash caterpillar ecm blank

[khadang]

hello all. please help me ho to flash for this ecm.
ecm is 80 pin and blank
thank so much advance!

[khadang]

up..up. anyone know how to flash this ecm please let me know, thank so much!

[ronshamal]

tell me what machine u need ride flash file nr

u need file conekt pin 1 power 12v p
pin 2 massa ground pin 3 and 9 cdl (d and e in cat conektor)

just put the file in!

[khadang]

thank you. i know pin connector to this ecm.
i using 24vdc because system power in this caterpillar dozer is 24vdc.
i don't know type of this dozer, i think is d6r.
part no of this ecm is: 132-2148 TRANSMISSION CONTROL.
I have used many version of caterpillar et from 2007c to 2011b (full service dealer et) but can't flash this ecm.
I have also used many file fsl in infomation from file : readxref.txt in flash disc.
i have cat adapter II and III but same result.
this ecm is blank i don't know cause,when I saw it it was so.
the monitor same on dozer when i conect caterpillar show: monitor not supported,
the dozer is verry old, i think maybe need cat et older version.
anyone know please let for me how to flash this ecm, dozer now dead.
thank you verry much.sorry my english bad.

[khadang]

i'm still waiting dk friend. can help me.

[ronshamal]

thank you. i know pin connector to this ecm.
i using 24vdc because system power in this caterpillar dozer is 24vdc.
i don't know type of this dozer, i think is d6r.
part no of this ecm is: 132-2148 TRANSMISSION CONTROL.
I have used many version of caterpillar et from 2007c to 2011b (full service dealer et) but can't flash this ecm.
I have also used many file fsl in infomation from file : readxref.txt in flash disc.
i have cat adapter II and III but same result.
this ecm is blank i don't know cause,when I saw it it was so.
the monitor same on dozer when i conect caterpillar show: monitor not supported,
the dozer is verry old, i think maybe need cat et older version.
anyone know please let for me how to flash this ecm, dozer now dead.
thank you verry much.sorry my english bad.

Pm me email i tell u all monitor not, conekt where are u location?what is the end of the ecm number ? Dk dc or di give prefix of machine i tell u what file, is it taking the file and than say emty pl explane more

[khadang]

hi friend,thank you for your help.
my email is: dongcosaigon@gmail.com
I'm in Viet Nam.
all infomation on ECM: 132-2148-04, umuudk-nn , 30770220dc
it talking the flash file, and then i close quick help, i click to select ECM to begin flash but Winflash show: ECM is not Flashable. File infomation and ECM/file information are auto disappear.
thank you and good day!

[mathura]

Someone please advise

This is a new ECM that came blank, when I attempt to start flashing I get this message " it is inapproiate to flash the ECM at this time service tool cannot determine the reason"

Machine SN: 3KZ00702
525B Skidder

Thanks

[dieselequipos]

FRIEND MATHURA WHAT FLASH FILE NUMBER YOU USE???

Someone please advise

This is a new ECM that came blank, when I attempt to start flashing I get this message " it is inapproiate to flash the ECM at this time service tool cannot determine the reason"

Machine SN: 3KZ00702
525B Skidder

Thanks

[mathura]

FRIEND MATHURA WHAT FLASH FILE NUMBER YOU USE???

The ECM is a new one that came blank, I requested a flash file and a member here gave this one to me based on the SN of the machine.

Flash File: 231-3867

This file when opened on et shows that it is for a transmission skidder. However this is the latest flash file so I want to try with another flash file or if someone can advise of any other procedure to get this file working.

Need older f file try: 229-4983 or 212-1435

Thanks

[ronshamal]

i know this problem put the ecm on the table to prog it put power on 24v then it works u can pm or send for me i help u

[dono]

You used ECM 2 2nd generation. It still remove and install Personality Module Chipset on below of ECM. On WinFlash menu, ET will show that. It mean that ECM can not be flashed.

[salwan]

hi dear
how are you
iwant ask you
this ecm use for what machine please