XPROG Clone Repair

[Raffy haddad]

hi all and thanks for this opportunity
actually i have a problem i have the xprog m v 5.0 and i tried to update it
so it is dead
i bought an usbasp s51&avr but also have error power on failed , i have communication with it ay usbasp found on port but power on failed
i changed the atmega64a and check everything pins out soldering everything
i connect it to tl866a with 12v power to xprog and cheked everything
when i press check id it say ff ff ff
when i try to read it says succeful and also if i say erase it says succeful
when i try to program it begen to program and then error adress 0x00000 ,buf val 0x0c , ic val 0xff
can any one explain me please what i did wrong ?
thanks

[pablobonome]

hello, how I can authorize the use of these micros?
AUTH-0023-1 MAC7xxx
AUTH-0023-2 XC23xx
AUTH-0024-1 MC9S12Cxx
AUTH-0024-2 MC9S12XE
AUTH-0024-3 9S12XE SECURITY
AUTH-0024-4 MC9S12HA/HY/P
AUTH-0025-1 MPC/SPC5xxx Authorized 11/4/2014

[serg2000]

hello, how I can authorize the use of these micros?
AUTH-0023-1 MAC7xxx
AUTH-0023-2 XC23xx
AUTH-0024-1 MC9S12Cxx
AUTH-0024-2 MC9S12XE
AUTH-0024-3 9S12XE SECURITY
AUTH-0024-4 MC9S12HA/HY/P
AUTH-0025-1 MPC/SPC5xxx Authorized 11/4/2014

no problem
pls wrote in PM

[pablobonome]

hello, the system tells me that you do not have space for private messages.

[sawatdee0999]

how can i authorized the use of these

AUTH-0023-1 MAC7xxx
AUTH-0023-2 XC23xx
AUTH-0024-1 MC9S12Cxx
AUTH-0024-2 MC9S12XE
AUTH-0024-3 9S12XE SECURITY
AUTH-0024-4 MC9S12HA/HY/P
AUTH-0025-1 MPC/SPC5xxx Authorized 11/4/2014

[CentralinasPt]

My XPROG 5:50 worked well, I update and now I can not read HC05, I work a lot with EZS and now to read 1D69j and another reads all the 000000

[majsterx]

I too can help with authorization, but little lower version.
>5.5... t many problems, unstable software, easy to brick mcu

[ddc]

sorry, but links for update on page 1 don't work...
check pls

[johnybilly]

Hello all,

I have update my Xprog 5.50 chinese that was dead. Now its working like never did, but i dont have any authorizations and update firmware gives an error. What am i doing wrong? Should the update firmware must be througt port R232?

2.jpg1.jpg3.jpg

Thanks

[electronistul21]

what version you have first time?

[johnybilly]

its was a 5.50 but i never manage to put it to work with sucess, so i downgrade it to the fix version in this post.

Thanks electronistul21

[johnybilly]

what version you have first time?

Can you give me the firmware 5.50 plus the SW 5.5 with all the authorizations?

if i could put it like it was originaly the better

thanks in advance mate

[johnybilly]

does anyone can help me? maybe i should buy another one and then fix my damaged one with the SW HW FW?

[kohli]

NO UPDAT FO TOOLS CHINA

[Zmann]

Two good and reliable versions available on this forum, classic v5.0 and v5.5.1 but the later you need to wait for the crack author, serg2000 to activate it. No matter if it's china hw as long it's not defective.