RNS315EU decode

[mbi]

For MBI what can be the problem .
i post video .https://imgur.com/a/WvAnA86 ,as you can see i have TX all the time 0 .
Regrads

Arduino doesn't receive any data from radio.
You have bad connection between arduino and pin 2 of connector at back of the radio.
Measure resistance between Atmega328P pin 30 and pin 2 of connector at back of the radio.
It should be about 1000 Ohm or less when jumper is in normal mode.

Check connection on the bottom side of arduino pcb.

I will send you e-mail with high resolution foto. It might help you.

[catalinosonesti]

I mesure and you know i have 2 Boards Arduino 1 with 5v rezistor i have 0 ohm.
Second with parallel 2 rezistor i have only 220 ohm.
I must by original Board?
Regrads

[mbi]

I mesure and you know i have 2 Boards Arduino 1 with 5v rezistor i have 0 ohm.
Second with parallel 2 rezistor i have only 220 ohm.
I must by original Board?
Regrads

It might be any arduino Nano, cheapest clones should works.
It should work if you have 220 Ohm or 0 Ohm. This resistances has protection function I think. Maybe they are diffrent on diffrent arduino clones but I don't think so.

I see on your video that program hanging because it waits for data frame on pin 30 (RX) of Atmega328p.

It must be connection between pin 2 on radio and pin 30 on Atmega328P.

[ganson]

mbi thank for info!!! I made code finder - works. Only the limit of 30 codes is not pleasant.

[catalinosonesti]

Hi
What im doing today , i put RX pin to 2 back of the radio and work .....till 3 atemps .
I make a short video , radio stop after 3 try and disconect from power .
when i try again same movie. https://imgur.com/a/KAiG6No
What can be ?

[mbi]

Hi
What im doing today , i put RX pin to 2 back of the radio and work .....till 3 atemps .
I make a short video , radio stop after 3 try and disconect from power .
when i try again same movie. https://imgur.com/a/KAiG6No
What can be ?

Sorry to say but it looks like my program is not working with your radio software version.
I attached new version (flash), program Atmega328 again and you can try it but I don't know if it will work.

Please send me what is your radio SW and HW version and production date from sticker.

[catalinosonesti]

Hi .
I try today with New Flash how send to me , but same result, no even jump to 0001.
I put Foto with sticker from radio.
Best regrads

[kappa1]

Hi .
I try today with New Flash how send to me , but same result, no even jump to 0001.
I put Foto with sticker from radio.
Best regrads

Try fast finger 0000-1999 or you can buy code from ebay...

[catalinosonesti]

Thx .
I know the code , from the navi , but i make this project below MBI Poland and for me is strange because locks like Martech .
For me is wery intresting , and i have time to try till i make it .
Regrads

[Decode Ghost]

I mesure and you know i have 2 Boards Arduino 1 with 5v rezistor i have 0 ohm.
Second with parallel 2 rezistor i have only 220 ohm.
I must by original Board?
Regrads

Hi.
My friend 220 ohm in its place 22 ohm Did you try ?

[mbi]

Hi .
I try today with New Flash how send to me , but same result, no even jump to 0001.

This looks looks like you have still problem with connection between pin 2 on radio and pin 30 on Atmega328P.

Either way, I'm afraid I can't help you more until I have this radio on my table.

[Decode Ghost]

Hi.
again, if not read try downgrading to Windows older versions

[Decode Ghost]

Hi.
you are using win10 win11 or win8 downgrade this version to win7, try process

[mbi]

Hi.
you are using win10 win11 or win8 downgrade this version to win7, try process

I'm afraid this will not help. In this case, the problem is elsewhere.

[Decode Ghost]

I'm afraid this will not help. In this case, the problem is elsewhere.

I don't know friend, everyone says this project has been done and worked, I just wanted to tell you possible mistakes