kess v2 clone

**mexanico1971** · 8th August, 2013, 09:36 PM

Originally Posted by atomiczen

today arrived new micro for my clone, that now work again
so solution for counter is definitely into the nxp micro.

hi !
what ref: have that npx ?!
thank"s in advance

br

**bbturbo** · 9th August, 2013, 05:02 AM

Originally Posted by soxten

Number of ecu?

The car is not with me yet. I'm trying to find out as much information as possible. As these models are not listed, I'm just not certain it can be R/W.

**bbturbo** · 9th August, 2013, 05:05 AM

Originally Posted by konopel

Only boot mode

Thanks. Have you R/W this car before? some ECU information will be much appreciated. Also do you have an idea where the ECU might be? I know it is in the engine bay but I heard it is in the front headlights.. is this correct?

**moky** · 9th August, 2013, 10:02 AM

someone tested kess on delphi dcm 3.5 Peugeot ? thanks

**moky** · 9th August, 2013, 03:56 PM

Just tested, kess work fine on psa rcz 2.0hdi 163hp delphi dcm 3.5 R/W ok

**kevfield** · 11th August, 2013, 03:17 PM

Hi all i have kess v2 china clone seems to ok with most stuff obd, tricore boot not so good anyway i have error when trying to install on the laptop i want to use it on , i have fresh install windows xp sp3 all netframe works java install and c++ but still no go ........ i have screen of what error is

Thanks kev

**bondiblu** · 11th August, 2013, 09:58 PM

Originally Posted by kevfield

Hi all i have kess v2 china clone seems to ok with most stuff obd, tricore boot not so good anyway i have error when trying to install on the laptop i want to use it on , i have fresh install windows xp sp3 all netframe works java install and c++ but still no go ........ i have screen of what error is

Thanks kev

Does yours have the resistor on the back if the PCB?

http://www.digital-kaos.co.uk/forums...93#post1953593

**kevfield** · 12th August, 2013, 12:42 AM

Yes mine has it on back , like i say it does work on one laptop and i can use it but i want to get it working on my x61s that i have bootit on it .......
Thanks for reply

Thanks kev

**kevfield** · 12th August, 2013, 06:47 PM

Solved wrong SD card folders no idea how it was working on one laptop and not the other......

Thanks kev

**ducatisti** · 12th August, 2013, 11:47 PM

Whats the drawbacks on the v2 clone ?

**galsy** · 12th August, 2013, 11:54 PM

not a lot for the money

**bondiblu** · 14th August, 2013, 09:28 AM

Finally received my MCU from my supplier, it arrived in a poor condition with some bent pins wrapped in paper and bubble wrap.

Anyway, after some time sorting it out and soldering it in place, it's all working again

so obviously per-programmed.

**overs0ull** · 14th August, 2013, 09:07 PM

Nice work - now all with the mcu- is fine . I still wait my to 2 mcu-s to arrive , to have for a case .
Regards

**atomiczen** · 14th August, 2013, 11:40 PM

Originally Posted by bondiblu

Finally received my MCU from my supplier, it arrived in a poor condition with some bent pins wrapped in paper and bubble wrap.

Anyway, after some time sorting it out and soldering it in place, it's all working again

so obviously per-programmed.

this micro need to be weld into a pcb for reprogramming, so for this reason every micro we'll receive will seems used

**bondiblu** · 15th August, 2013, 09:45 AM

Originally Posted by atomiczen

this micro need to be weld into a pcb for reprogramming, so for this reason every micro we'll receive will seems used

I do understand that fact, but at least package it correctly to avoid the fine pins getting bent and maybe ESD should be considered. A piece of paper and bubble wrap is not sufficient in my opinion, especially when it's not the easiest chip to lay.

At least it works right