Hi Peter, what is the fault with your car? I have immo active. No reader coil activity
Hyundai Coupe-Tiburon BODY MODULE
Hello immo experts,
can anybody upload working dump from HYUNDAI COUPE 2002-2006 BODYMODULE please?
Need full data backup from HC908 /2J74Y/.
Original 95410-2C160 but have many newest replacement variants, important is 4cylinder engine.
Many thanks for check yours archives.
regards!
Hi Peter, what is the fault with your car? I have immo active. No reader coil activity
Xprog-m, CarProg, MPPS,
AK90
SBB
VAS5054a
SuperVag K+CAN plus
AD900
CN900+4D decoder box
4D Cloner
Toyota smartkey maker
Volvo Vida DiCE
BMW GT1 DIS SSS Progman
+loads more chinese stuff
+ the excellent help of DK forum!
hello friend,
my symptoms:
-not start
-not fully diagnosable with original Hi-Scan, only some functions works
-not work power windos
-not work part of exterior lights
-not work remotes
-still /igni key switch off/ present 125khz on reader coil
after replace HC908 /with full dump from 2.7i version/ my car alived, but there is not possible match it with engine because immo topology is different on 2.7i engine than 1.6 or 2.0 engines.
Last edited by PeterOBD; 19th July, 2013 at 01:50 PM.
Anyone got a dump from BCM 4 cylinder? I replaced PCF chip and checked 5V supply etc. MCU not requesting key read from pcf.
Xprog-m, CarProg, MPPS,
AK90
SBB
VAS5054a
SuperVag K+CAN plus
AD900
CN900+4D decoder box
4D Cloner
Toyota smartkey maker
Volvo Vida DiCE
BMW GT1 DIS SSS Progman
+loads more chinese stuff
+ the excellent help of DK forum!
send your dump pls, my one is here
http://www.digital-kaos.co.uk/forums...module-344711/
I looked at your dump, it is .ori file, when I open it in hex editor it is huge and doesnt look like a normal file. Have I done something wrong?
Xprog-m, CarProg, MPPS,
AK90
SBB
VAS5054a
SuperVag K+CAN plus
AD900
CN900+4D decoder box
4D Cloner
Toyota smartkey maker
Volvo Vida DiCE
BMW GT1 DIS SSS Progman
+loads more chinese stuff
+ the excellent help of DK forum!
its regular binary file, dont know what is the problem on your editor
Today fitted 2nd hand BCM replaced old 2C160 with 2C440. Disposed of key used when reader coil died, programmed new key + old spare key with CarmenScan, no problems at all.
Was not prepared to read 2C440 MCU as used module cost $1200NZ. Customer paid. Could have got 1/10th the price on ebay
Xprog-m, CarProg, MPPS,
AK90
SBB
VAS5054a
SuperVag K+CAN plus
AD900
CN900+4D decoder box
4D Cloner
Toyota smartkey maker
Volvo Vida DiCE
BMW GT1 DIS SSS Progman
+loads more chinese stuff
+ the excellent help of DK forum!
thanks for message but Im sorry, still dont understand - do You use second-hand module or new one?
1200usd is regular price for new module, I think
Last edited by PeterOBD; 31st July, 2013 at 10:17 AM.
Fitted a used module from a 2005 4cyl. Which has the later part number, I had neutralised ECM playing around before, but just programmed new key and old key with PIN from chassis number and all worked fine. Our price through dealer was $2550+15% tax, that was the retail, trade would get less 10% probably, rediculous considering there are more electronics in a $100 DVD player
Xprog-m, CarProg, MPPS,
AK90
SBB
VAS5054a
SuperVag K+CAN plus
AD900
CN900+4D decoder box
4D Cloner
Toyota smartkey maker
Volvo Vida DiCE
BMW GT1 DIS SSS Progman
+loads more chinese stuff
+ the excellent help of DK forum!
aha,thanks for usefull info.there was available regular procedure in Carman for adapt used board unit or You play with it before coding keys?
mean adapt body to engine
Last edited by PeterOBD; 31st July, 2013 at 10:18 AM.
No procedure to adapt bcm. BCM is not programmed to immo at all, if anything it is just a signal processing point, all immo info is in ECM and programming is done via ECM not BCM. Procedure is called "teaching" in Carmen, I could have used SBB but Carmen has 'genuine' Kia and Hyundai software apparently. SBB would have been much faster. I did porgram under Elantra coupe, not Tiburon as no function was available for Tiburon. As you know, just get the correct part number I think you need 2C440 also right? there is one for cheap on ebay in Lithuania, guy was helpful in offering to post it to me
Xprog-m, CarProg, MPPS,
AK90
SBB
VAS5054a
SuperVag K+CAN plus
AD900
CN900+4D decoder box
4D Cloner
Toyota smartkey maker
Volvo Vida DiCE
BMW GT1 DIS SSS Progman
+loads more chinese stuff
+ the excellent help of DK forum!
must read maual for refresh, i forgot all on this area. thema is old and my head is poor
it is for me strange that you use successfuly elantra profile because it use SMARTRA not BODY by me.
i will use carman/HI-Scan/ too
I think you could just fit the BCM and not worry about immo because data is in ECM. It will start straight away with no programming
Xprog-m, CarProg, MPPS,
AK90
SBB
VAS5054a
SuperVag K+CAN plus
AD900
CN900+4D decoder box
4D Cloner
Toyota smartkey maker
Volvo Vida DiCE
BMW GT1 DIS SSS Progman
+loads more chinese stuff
+ the excellent help of DK forum!
ok Peter I have read my BCM using carprog as HC908AZ32 4L52H as mine is a 1L52H. EEPROM only as carprog said mcu does not support flash reading. It looks a lot different to yours, but mine would not start obviouslytiburon bcm.zip
Xprog-m, CarProg, MPPS,
AK90
SBB
VAS5054a
SuperVag K+CAN plus
AD900
CN900+4D decoder box
4D Cloner
Toyota smartkey maker
Volvo Vida DiCE
BMW GT1 DIS SSS Progman
+loads more chinese stuff
+ the excellent help of DK forum!
capi (21st July, 2018)
Bookmarks