lost correct map of Fiat Punto 2003 Delphi

[Belloriccoefamoso]

Halo
big big problem of last auguast. Near desperation
Please please can some one give me an help?
Customer lost all keys, i have TMPRO and use usually module 7 for this.
i try programmed 2 transponder but both no work
i can't program trought odb because SBB say "conencted" but ECU not recognized.
Big problem
i Suspect tmpro saved eeprom as 8 bit but in real is a 93LC66 (16bit)

NOW the big problem
i dont find where i put original map saved

i suspect i deleted it wrong

so i can't back to original map.

we tried disable immo in ECU, nothing change
so,... what can i do?
thanks in advance for your help!!!

[Belloriccoefamoso]

i near desperation...
customer shouting without car from a week....

[paul_12345]

post the dump you have

[Belloriccoefamoso]

fortunately i found old dump
customer found key and car start
BUT
the problem now is: what was wrong????
now i can post old and new dumps
defect with new dump and 2 new keys programmed: keys not start veicle, sbb silca can't conenct to ECU (connected, ECU not recognized) , and last thing when turn key all ok on dashboard BUT we didn't listen the fuel pump work (usually when u turn key u listen fuel pump for 1/2 seconds)
can someone help me in understand?fiatbin.zip

[Belloriccoefamoso]

just to be clear: in past i made many keys ID48 with tmpro and module 7
i know how sold and technichan told me solder of eeprom was right
i send the 2 dump now to Bogi, mister tmpro, and told me the 2 dump are correct...
but was impossible program new keys
and the real lucky thing is that customer found the old key, and i recovered dump from deleted file......
but why this time evenif everythink seem correct... noone key work and i have some defects?

[amper]

Dump read swap.
This may be the reason trouble.

[Belloriccoefamoso]

please can you explain ? i didn't understand

[amper]

Some programmers read and write byte swap.
Your reads the byte swap .

[amper]

Does not match the number keys.

[Belloriccoefamoso]

ok thank you but i don't know what does it mean, i don't understand why now did this and other times worked perfectly.
i don't understand this

[Belloriccoefamoso]

ok thank you
i don't know how can it be possible
i had read it with TMPRO
tmpro don't let me choose...i only can select "93c66"
no section of swap or 8/16 bit... nothing....

[paul_12345]

ok thank you
i don't know how can it be possible
i had read it with TMPRO
tmpro don't let me choose...i only can select "93c66"
no section of swap or 8/16 bit... nothing....

use the old file and swop the bytes then add key and see if tmpro swops the bytes when saving.

I've just made a little program to swop bytes I'll upload on another thread incase anyone else wants to use it.

http://www.digital-kaos.co.uk/forums...4/#post2070464

[Belloriccoefamoso]

con someone explain me what does it mean

"swap" into a map ?
And which effects do the operation of "swap the file"?
thank you a lot

[paul_12345]

con someone explain me what does it mean

"swap" into a map ?
And which effects do the operation of "swap the file"?
thank you a lot

use the original file read with tmpro, then drag that file onto the exe of the program I made, this will create a new file.

The new file should be ok to put back onto the car, but if you want to add a key first, then load this file into tmpro and precode the keys then add them to the dump.

Then post the dump here to make sure tmpro hasn't messed the file up, if its ok you can write the new file into the eprom and you should be ok.

[Belloriccoefamoso]

paul thank you to tell me the right procedure
but my question original was another....
i mean the "literature"...what does it mean "swap file" and what this operation do teorically
thank you in advance