Tricore Virgin Solution Software ?

[atomiczen]

New functions :
(available online by MMS Helpdesk)Finaly it's possible to recode used Tricore ECUs even with OTP sectors:
ECU CLONE:
VAG EDC17 C46 TPROT8-10
VAG EDC17 CP44 TPROT8-10
VAG MED17.1 TPROT8-10
VAG MED17.1.1 TPROT8-10
VAG PORSCHE MED17.1.6 TPROT8-10
OPEL EDC17CP19 improved
Renault SID305 improved
BMW EDC17CP02 improved
BMW EDC17C06 improvedDPF-OFF:
MB EDC16C3/C33 improved
DODGE EDC16C31
KIA/HYUNDAI EDC17CP14
Opel Insignia EDC17xx
VAG EDC17U01EGR-OFF:
RENAULT EDC16C3/C33IMMO OFF
(available for motorsport purposes only)
VAG MED17.x all TPROT versions
VAG EDC17CPxx/Cx all TPROT versions
VAG MED9.1
PSA EDC16Cxx

I repeat to everyone another time, i called Magpro warehouse, they tell me that they sell an immo off solution for a 1:1 edc17 vag clone, they write fake information on web
they cannot clone 1:1 a tprot vag edc17, they can only make an immo off. Remember!!
this is what they tell me: software cannot do this procedure stand alone, you have to make a full readout, send it to magpro, then they send to you a file to write into the new ecu......this is a 1:1 clone procedure??? i think no.....

[jnoroeste]

Hi,

About OTP areas... could be possible write in no OTP areas (empty code zones) and redirect the instructions as it were in OTP ones?

As OTP can?t be rewritten, need to write in another place, or swap new & programmed processor with used data , isn?t it?

Regards.

[soxten]

jnoroeste: I think this could be a good way to go!

may I ask, Do Fgtech/X17 Tool/K-tag read all info on TC1796 (inc. OTP area?)
IF, then it is possible to mount a new TC1796 mcu on ecu and program
OR?

[solitaire]

Abritus released new update for VAG:
* !!! HIT !!! EDC17/MED17 immobilizer bypass through boot-mode
* !!! HIT !!! By OBDII adaptation of Immo V engine control units and BCM2 modules
* !!! HIT !!! Recalibration of control unit mileage - EDC17/MED17 through boot-mode
* !!! HIT !!! Transfer PIN/CS/MAC from one EDC17/MED17 to anotherthrough boot-mode
* Fix the checksums in EDC17/MED17 flash

[jnoroeste]

jnoroeste: I think this could be a good way to go!

may I ask, Do Fgtech/X17 Tool/K-tag read all info on TC1796 (inc. OTP area?)
IF, then it is possible to mount a new TC1796 mcu on ecu and program
OR?

Even getting a full backup.. should not be possible to write in another computer due to OTP areas, so .... perhaps.... new chips and virging codes........
I think this is the challenge for all chiptunning companys, all of them are working hard.but they need time to do it in safe way.

Regards.

[ominimicu]

Ican now do Immo off on all VAg edc17 with no need of eeprom just flash....so let them sell their lies

[boomeer]

Is your solution work 100%?

Отправлено с моего GT-I9300 при помощи Tapatalk

[hollow]

Ican now do Immo off on all VAg edc17 with no need of eeprom just flash....so let them sell their lies

il keep that in mind

[ecutuners]

Flash solution been around long time longer than eeprom solution

[ominimicu]

Yes works 100%, Danny i dunno how long it has been out...but i searched all web upside down..no one oferes no info unless its for money!
And i think i can also virginizze other edc17 like pSa, opel, renault! i need someone to do tests

[boomeer]

so what's the difference between eeprom and flash solution?

[ominimicu]

no idea....i never got to the eeprom solution. maybe there s some info in eeprom to unlock Trprot..ot smth

[boomeer]

hm may be mr.ecutuner tell as the difference?

[soxten]

Is it possible to read all info on mcu and program to a brand new mcu?
If I take a used ecu and mount a brand new mcu and then program info from customers broken ecu?

[H.Wessel]

Abritus released new update for VAG:
* !!! HIT !!! Transfer PIN/CS/MAC from one EDC17/MED17 to anotherthrough boot-mode

hello

This is common ecu adaptation (not clone) and can be done via boot or by obd.
I tested both with original Avdi and works but for obd procedure previous ecu pin/cs must be know.

best regards
H.W