Chineese Galletto V54

**Pietrek** · 10th December, 2019, 01:43 PM

EDC 16 Simos3,2 pinout please

**cocktailyogi** · 27th December, 2019, 09:26 AM

Hi I got a chinese Galletto V54, reflashed it, changed resonator and it works.

Now I have a problem with my Audi A4 2009 ECU. It is a MED17.1 via CAN

I can read and write this ECU in Bootmode with Galletto very well.

But I cannot read or write via OBD. Neither on bench with disabeld immo or in car.
Galletto always tells me that ECU-wakeuo failed. Same issue with MPPS16.

What could be the problem? Has this ECU another protocol? I am nit sure if the problem is on ECU or Galletto-side. Bootmode works great.

Kind Regards,
Yogi

**Orchid70** · 26th January, 2020, 01:30 PM

Hi
In the learning business and mostly looking for a tool for reading and writing (files that someone else have but together for me =)
In Sweden and have cars from 2000-2017.
Would this be a good option for me:
http://www.obdii365.com/wholesale/fg...u-version.html

Thanks!!

**turbo16v** · 26th February, 2020, 12:46 AM

low quality board or clone of cloneAttachment 694027

**Stelaras26** · 26th February, 2020, 10:04 AM

Originally Posted by Orchid70

Hi
In the learning business and mostly looking for a tool for reading and writing (files that someone else have but together for me =)
In Sweden and have cars from 2000-2017.
Would this be a good option for me:
http://www.obdii365.com/wholesale/fg...u-version.html

Thanks!!

Thats the best chinese pcb that is out.

**Stelaras26** · 26th February, 2020, 10:06 AM

Originally Posted by turbo16v

low quality board or clone of cloneAttachment 694027

Search for Fantomels threads,you can rework it somehow and make it a lot better!

**turbo16v** · 26th February, 2020, 09:06 PM

[QUOTE = Stelaras26; 3805886] Suche nach Fantomels-Threads, du kannst es irgendwie überarbeiten und es viel besser machen! [/ QUOTE]

I can't even install proper capacitors because there are no holes in the board

fantomel did a great job here!!

**tango** · 29th February, 2020, 03:28 PM

that board of yours is crap sorry
never seen 1 with smd caps instead of the normal electrolitic caps before
if there is no through holes for normal caps then you could replace the ceramic smd caps for proper smd eletrolitic caps instead which will work just as good

**giriprakash1978** · 14th March, 2020, 05:11 PM

hi....i have to read KIA ECU EDC15C7 this one not have support on Ktag......i have Geleto V54 clone this device have support with EDC15C7 Alfa remo please some have how to connect ECU with Geleto......please help......i try to read AM29F400 it is password protected....

**morgano** · 14th March, 2020, 06:54 PM

That edc15c7 you can read with any tool that supports C16x processor bootmode. Ktag should do if you choose ME7 ecu with same flash chip. Also galletto read it bootmode selecting ME7 protocol.

**giriprakash1978** · 21st March, 2020, 02:31 PM

thanks man, KESS can read by OBD2 Kia ECU EDC15C7.......and Gelletto also read EDC16C2 on table only have to ware Kline and +Ve and -Ve

**slawarek** · 15th April, 2020, 10:19 PM

After update 386 to 475 fgtech v54 will read AcDelco E83? (or other mpc5565).

**MIKUr1** · 9th May, 2020, 11:01 PM

Actually the PCB from photos above, can properly be reworked. I bought SMD electrolitic caps with proper capacitance, removed from them plastic base, and soldered "standing" with theirs legs on pads on board. It works like a charm. Never failed.

**drinkyboy** · 21st May, 2020, 04:52 PM

Hello,
Can anyone help me how to connect to motherboard on this tipe V54?
I founded the RX, TX, and Gnd but i dont know how to use that jumper pinout so i could flash the LPC..

Thanks!