VVDI PROG

**taxo1965** · 15th February, 2018, 02:37 PM

Yesterday I received a VVDI Prog.
Tested: Many thanks to the developers.
906 sprinter 2007 9s12 Read/Write eeprom-flash ok
immo Vito 908 0j66d Read/Write ok
w211 2005 9s12 Read/Write eeprom-flash ok

S9S08DZ60 (2M74K) Immo IK BYD 2011
sorry protection can not get around.I hope the developers will solve this problem
Eraze+Unlock works checked, my block for spare parts

Best Regards

**sniegavirs** · 15th February, 2018, 03:04 PM

Originally Posted by obeids

Which is the best programmer for CAS4?
The VVDI gave me grief and it seems to have killed the CAS.

VVDI Prog is great for CAS4! It is not tools fault that you obeids were not careful enough doing your job. And with correct PFlash and DFlash your Cas4 could be working again but that depends only on you yourself. I have done around 11 CAS4 at the moment and never had any problems!

**Maartinj** · 15th February, 2018, 10:22 PM

Originally Posted by sniegavirs

VVDI Prog is great for CAS4! It is not tools fault that you obeids were not careful enough doing your job. And with correct PFlash and DFlash your Cas4 could be working again but that depends only on you yourself. I have done around 11 CAS4 at the moment and never had any problems!

100% agree

**sniegavirs** · 16th February, 2018, 06:44 AM

Had a chance to play with BMW X4 F26 Airbag unit ACSM4 due to internal pcb element problem. Did not find any information on how to properly read this unit since it is glued together as seen in pictures so i cutted the case carefully and now if needed i will only cut out a little window at the corner(shown in picture) to read/write the unit. Only those 4 pads needed 1. BKGD 2.VCC 3.Reset 4.GND Maybe Xhorse can take this information to VVDI Prog software.
Only memory on PCB is MCU 9S12XET512 (UNSECURED)
These Airbag units also installed on BMW F25 X3 and F10/F11 5series

**Batumeli** · 16th February, 2018, 10:56 AM

Hello!
my programmer vvdi prog stopped reading the processor 9S12 secured.
Not in MB locks and not in CAS. Maybe someone's got a problem with such a problem? In the technical support wrote not who did not answer!

**exe123** · 16th February, 2018, 12:21 PM

16-26.02. is Chinese New year. You will not get any support during this time

**tibibond** · 16th February, 2018, 08:09 PM

reposted with proper quotes

**tibibond** · 16th February, 2018, 08:09 PM

Originally Posted by sniegavirs

Had a chance to play with BMW X4 F26 Airbag unit ACSM4 due to internal pcb element problem. Did not find any information on how to properly read this unit since it is glued together as seen in pictures so i cutted the case carefully and now if needed i will only cut out a little window at the corner(shown in picture) to read/write the unit. Only those 4 pads needed 1. BKGD 2.VCC 3.Reset 4.GND Maybe Xhorse can take this information to VVDI Prog software.
Only memory on PCB is MCU 9S12XET512 (UNSECURED)
These Airbag units also installed on BMW F25 X3 and F10/F11 5series

send a pm if you need dump, i have one reading from a good unit and you can test if internal fault goes away

**sniegavirs** · 16th February, 2018, 11:34 PM

Originally Posted by tibibond

send a pm if you need dump, i have one reading from a good unit and you can test if internal fault goes away

Thanks but no need. By internal i meant that something on the PCB is damaged after the crash of the car! Now it doesn't recognize new airbag replacement. Tested the wires and all is ok. Even connected ~3ohm resistor to test if it is airbag fault but still nothing. But when i shortcircuit those 2 wires it recognizes that the resistance is too low so it means something on the PCB is blown out due to activation of airbag while crash happaned. I will be changing the ACSM unit.

**mickye_dj** · 18th February, 2018, 11:21 PM

od66j motorola hc908 not working in circuit

**djjazzer** · 19th February, 2018, 05:43 AM

Was able to read eeprom & flash of W211 with VVDI Prog, but now EIS dead, no power, immo coil tested no light. Rewrote new flash, still dead. Used doner EIS before connecting to VVDI Prog, tested immo light would come on, now after read and write doner EIS not lighting up, dead. What's the deal?

Sent from my ASUS_Z00AD using Tapatalk

**djjazzer** · 19th February, 2018, 08:08 PM

Originally Posted by djjazzer

Was able to read eeprom & flash of W211 with VVDI Prog, but now EIS dead, no power, immo coil tested no light. Rewrote new flash, still dead. Used doner EIS before connecting to VVDI Prog, tested immo light would come on, now after read and write doner EIS not lighting up, dead. What's the deal?

Sent from my ASUS_Z00AD using Tapatalk

Maybe this board is not supported by VVDI Prog? Had to use Smok diagram for reading. EIS is 2115452308

Sent from my ASUS_Z00AD using Tapatalk