VVDI PROG

[cavignac]

Hello everyone
VVDI Prog reads and writes AMD 29F400?
thank you

[louis21]

Hi friends sorry I write wrong chip No.
vvdi prog support R5F21548G?
thank in advanced

Yes,support.In the 2-MCU,RENESAS-R8C

[ucokseparoh]

Hi guys.. anyone well-grounded that can help me with this confusion please ?

I got some money to spent and is thinking to expand my services to BMW (EWS & CAS 1/2/3 - may be not for the latest CAS yet).. and is looking for a programmer. I already have Tango for starter.. do you guys think Tango + VVDI Prog is a wise choice and enough for the job i'm planning to cover (spare key adding and all key lost)? I was told that for EWS 1/2 i may need AK90 as well because VVDI Prog can't read it?

I have read the thread from first page to the end, but since i'm not a practitioner yet in this auto brand, thus my knowledge is not as good as you guys, i'm afraid i may end up buying the wrong device. So, some advices from you guys will be helpful and much appreciated.

Should i go for VVDI Prog or Orange basic (without Immo HPX) ? Or may be there is another option you guys can suggest me?

Thanks for any helps.. best regards.
.
.
PS : My apology if this question is not suppose to be here.

[ucokseparoh]

- double post

[Maartinj]

Should i go for VVDI Prog or Orange basic (without Immo HPX) ? Or may be there is another option you guys can suggest me?
Thanks for any helps.. best regards.
PS : My apology if this question is not suppose to be here.

somebody who use VW never recommend BMW
hope you find people who use both

[doctore]

my mistake

[louis21]

Hello everyone
VVDI Prog reads and writes AMD 29F400?
thank you

can't read and write temperorily,will add it.

[bero]

@bero
Try it several times!
When problems occur, disconnect the PCf from + 3v for a while, Pcf without power
Vvdiprog works at 3.5v put to 3.6v.
If it still does not read, it has corrupted the PCF lock code and can not restore. Because vvdiprog does not recognize it. This possibility is scarce but existent.
All this recognizing that you have done the normal manual procedure.

sorry for the late answer, i was a week away.
I tried also diverent volts if you mean the +3v from the cable (red one) i tried that also..

Lucky, the PCF is not dammaged, and operates normaly

There was also someone asking of snapshot pictures, but since i updated the software, the logs are gone, and don't have the remote here anymore

[dorofteius]

I made pcf reseting with vvdi prog on allot of remotes. It does erase, no problem. It writes no problem.
Thumb's up for the tool. Working good.
Only that you need a good dump for the pcf.

[Basti13]

Hello everyone
VVDI Prog can read and writes tricore tc-1797 ?
thx for info .

[sniegavirs]

Hello everyone
VVDI Prog can read and writes tricore tc-1797 ?
thx for info .

No. And those Tricores it can read is only some VW ecu's because VVDI Prog don't have security bypass for other... For example: Audi A3 ECU with tricore TC-1762 it cannot read!

[sv2hqx]

hi
possible to add 9s12q128 0m66g ?
thank you

[recodes]

Read MC9s12xdg128 2M42E tonight. Very smooth easy read and verify flash and eeprom. Security bit is at 1ff0f and is 0xfe unsecured.
I erased the eeprom then erased the flash thinking of course the software would not be written so as to secure the chip and will write security byte 0xfe....
No chip is now locked!!! Why do this?
How do I recover the chip now please?
Thank you

[obeids]

Hi

I have successfully read VW Beetle cluster with HC912.....
Can I upload picture of the Cluster board and pinouts so that X-Horse can add it with diagram photo in the software?

[PremierD]

Of course you can mate ....