VVDI PROG

**Maartinj** · 22nd February, 2019, 08:01 PM

Xhorse 2019 Catalog

English version

Polska wersj

**sadarmeng** · 23rd February, 2019, 01:31 AM

Anyone have read renesas 70F3577 daihatsu BCM? i have read new bcm but cant stable, every read, always displays different data, I try the environment Read + verify, always ask to be reset, after that device error, does my vvdiprog have a problem?

**maxim200** · 24th February, 2019, 07:10 PM

are there any adapters MC9S12 80QFP, 112QFP? available for vvdi prog ?

**rob h** · 24th February, 2019, 08:02 PM

No 80 or 112qfp adapters, you could make your own.
Best buy Chinese upa programmer with all adapters, or xprog full.
Way cheaper, and always good to have more then 1 programmer.

**PerryZhang** · 25th February, 2019, 03:23 AM

Originally Posted by sadarmeng

Anyone have read renesas 70F3577 daihatsu BCM? i have read new bcm but cant stable, every read, always displays different data, I try the environment Read + verify, always ask to be reset, after that device error, does my vvdiprog have a problem?

hi，we will check that , do not reset if you have problem like that , it will damage you data if you reset ,

**kristikapa** · 25th February, 2019, 09:32 AM

I am trying to read R7F701019 in kia airbag module 95910-h8210 and I always get different readings for some sectors. Other sectors are always the same. Can anyone check this?

Smok website states that jtag will read random values for unused sectors. Is this the case for vvdi prog too?

**PerryZhang** · 26th February, 2019, 03:35 AM

Originally Posted by kristikapa

I am trying to read R7F701019 in kia airbag module 95910-h8210 and I always get different readings for some sectors. Other sectors are always the same. Can anyone check this?

Smok website states that jtag will read random values for unused sectors. Is this the case for vvdi prog too?

you can try set the VCC to 3.3v and see if work , VCC is in the right-up corner of vvdi prog software

**kristikapa** · 26th February, 2019, 08:41 AM

Originally Posted by PerryZhang

you can try set the VCC to 3.3v and see if work , VCC is in the right-up corner of vvdi prog software

For this module smok states to use 3.3v. I tried different voltages from 3.3V to 4V and nothing changed. I was afraid to go higher with the voltage not to damage the module.

**Samic** · 28th February, 2019, 05:01 AM

VVDI PROG latest software version V4.8.0 update

-------------------------------------
v4.8.0 (2018-2-27)
* This version DON't need update firmware
+ Add VVDI PROG USER MUNUAL 4.8.0 version in Doc folder
+ Add 25AA010, 25AA020, 25AA040, 25AA080, 25AA128, 25AA160A, 25AA160B, 25AA256, 25AA320,25AA640, 25LC160A, 25LC160B,
25LC1024 options in <1-EEPROM&FLASH>-><MICROCHIP>
+ Add 25AA010(CLIP), 25AA020(CLIP), 25AA040(CLIP), 25AA080(CLIP), 25AA128(CLIP), 25AA160A(CLIP),25AA160B(CLIP), 25AA256(CLIP),
25AA320(CLIP), 25AA640(CLIP), 25LC160A(CLIP), 25LC160B(CLIP), 25LC1024(CLIP) options in <1-EEPROM&FLASH>-><MICROCHIP(CLIP)>
+ Add MB91F534B options in <2-MCU>-><FUJITSU-MB9XF>
+ Add MC9S12XS64_SECURED, MC9S12XS128_SECURED, MC9S12XS256_SECURED options in <2-MCU>-><MOTOROLA-MC9S12>
+ Add R7F701071 options in <2-MCU>-><RENESAS-RH850>
+ Add F_ENGINE_MEVD1723(F20)EEPROM options in <3-ECU>-><BMW>
+ Add F_ENGINE_MEVD172K(F20)EEPROM options in <3-ECU>-><BMW>

Notes: please keep using latest version software, any problem post here or PM technical support.

**taxo1965** · 28th February, 2019, 06:49 AM

Dear friend, @Samic,please add R7F701A223 Toyota Camry SRS.Thanks

**autoTkey** · 28th February, 2019, 06:50 AM

Still no support for some of the oldest motorolas...

**conbee70** · 28th February, 2019, 10:50 AM

Hi All. I need some advise. I am wondering if there is something wrong with my VVDI prog. I do a lot of 8 leg IC eeprom for immobiliser so I bought the VVDI Prog and clip so I can read some of these chips in circuit. I have tried it about 20 times so far but have only been able to read 2 ICs in circuit.
This pass week I have tried the following

Saab 9-3 IC 93lc66 Failed - Says data read sucess but eeprom file all blank. All Zeros

Toyota Yaris IC 95080 - Failed. Keeps saying Chip Not Connect

MK6 Gold IC ST 24c64 - Failed - Says data read sucess but eeprom file all blank. All Zeros

MK6 Gold IC ST 24c32 - Failed - Says data read sucess but eeprom file all blank. All Zeros

I tried reading the data on each IC at least 5 times and I am certain the clip was connected properly. I also made sure that both clip and IC's are clean. I always resort to removing IC and using different programmer to read and write eeprom data.

Any advise will be much appreciated.

**PocketHero** · 28th February, 2019, 10:56 AM

A lot of cases they can't be read on board. Buy a dip8 and desolder.
Other hand the chips pins need always be cleaned, I prefer light fileing
Usually I try 5-20 times to have good contact before I can read the content ön board

**amrif** · 28th February, 2019, 12:15 PM

Originally Posted by gif_kuba

New test:

1. MPC5607B 0N69H - readed correctly with external power
2. MC9S12XEQ512 3M25J - Unsecured - read with external power - but give partition error so must manually set dflash/eee size

I have problem with this BCM, do you have pinout??

**daxxer** · 28th February, 2019, 12:55 PM

Originally Posted by PocketHero

A lot of cases they can't be read on board. Buy a dip8 and desolder.
Other hand the chips pins need always be cleaned, I prefer light fileing
Usually I try 5-20 times to have good contact before I can read the content ön board

yes....or can be read but cant be writed..

in some cases can help connecting the one or two separate wire to GND on pcb

for 100% results are best method desolder-read-modify-solder back

clip are mostly for lazy people only, but i understand....it can save lot of time and work