VVDI PROG

[LEORNARD NKATA]

hie all
i have a problem with my device it cant be detected by the pc what could be the problem l
i have checked the usb port and it looks fine

thanks in advance

[Maartinj]

hie all
i have a problem with my device it cant be detected by the pc what could be the problem l
i have checked the usb port and it looks fine

thanks in advance

check with other PC, make sure no driver issue
if still "faulty" contact your seller to help you return to manufacture

[xjojo]

Hi
I have a problem with reading D70F3506
I checked all possibilities several times
receives a message - try frequency failed
vvdi 4.8.5

[hivrich]

Hi
I have a problem with reading D70F3506
I checked all possibilities several times
receives a message - try frequency failed
vvdi 4.8.5

Look at the quartz near D70F3506

[xjojo]

I have a problem finding him.
is it not possible?
And what are you going to ask about quartz?

[hivrich]

I have a problem finding him.
is it not possible?
And what are you going to ask about quartz?

100pin - 14,15pins quartz
144pin - 23,24pins quartz

see connection instructions

[xjojo]

ok
144 - quartz - I found
will you tell me what to do?
remove? bypassed ?

[hivrich]

ok
144 - quartz - I found
will you tell me what to do?
remove? bypassed ?

I think to see the frequency of quartz and set it in the programmer

[xjojo]

my knowledge on this subject may be poor
the quartz mark is 0162k or D162k - hardly visible.
possibly, how can I measure it?

[no__name]

On Vvdi prog, i have a ecu Vespa gts , mcu stm8s207cb inside , when i press read eeprom, flash whatever , read some 00 00 00
Regards Michal

[ibratex]

Delphi MT86 (3500) Gearbox
Hyundai - Kia

-Read and write ok by ECU reflash cable
-Pinout some as VVDI-Prog manual
-Other operation some as picture



( The power should be disconnect and connect before each operation )



Sent from my iPhone using Tapatalk

hello how are you , all freinds , i am trying to clone mt86 with 2 infinion inside , i tried to read with vvdi prog the old ecu it says chip not connected i did exactly as the help in vvdiprog

what am i doing wrong , the old ecu have only 3 coils working i dont know what component is for the coils so i decided clone on other one


car start with old ecu , and also i tried to read with combiloader it read flash normally i copied on donor ecu but car didnt start so i want to copy whole flash and eeprom with vvdiprog but always chip not connected ,


anyone have or had same problem ?... please maybe helping with showing me with coils responsible component also helps alot , thanks in advance

[CarCity]

hello how are you , all freinds , i am trying to clone mt86 with 2 infinion inside , i tried to read with vvdi prog the old ecu it says chip not connected i did exactly as the help in vvdiprog

what am i doing wrong , the old ecu have only 3 coils working i dont know what component is for the coils so i decided clone on other one


car start with old ecu , and also i tried to read with combiloader it read flash normally i copied on donor ecu but car didnt start so i want to copy whole flash and eeprom with vvdiprog but always chip not connected ,


anyone have or had same problem ?... please maybe helping with showing me with coils responsible component also helps alot , thanks in advance

My friend
In the Delphi MT86 you have 2 Tricor _ TC1766 ( Motor + Gear box )
To read TC1766 motor you should use this method :

Raise PIN 122

1.jpg

2.jpg

[ibratex]

i should not lift any pin ?

[CarCity]

i should not lift any pin ?

PIN 122 should be lift

[ibratex]

i lifted and tried 2 ecus same problem i dont know what is wrong . i changed resistors also its 0.995 kohm = 1000 ohm (Brown, Black, Red, Gold ) color code each and the obd conections are clear but not reading . tried combiloader read ok but only map area i need full , waht would be wrong :S