VVDI PROG

[phatty123]

Bosch adapter tested with bmw ecu and did not have success

[2019-09-14 18:24:08] : Communicating... 94%100
[2019-09-14 18:24:12] : Communicating... 100%100
[2019-09-14 18:24:30] : 7 Chip enter failed

[daxxer]

Bosch adapter tested with bmw ecu and did not have success

[2019-09-14 18:24:08] : Communicating... 94%100
[2019-09-14 18:24:12] : Communicating... 100%100
[2019-09-14 18:24:30] : 7 Chip enter failed

can you post label of ecu ?

[phatty123]

can you post label of ecu ?

dont have ecu close by but I have part # in notepad
0261s06727
7619981

Different part # 0261s10196 from F10 n55 I was able to read dflash with adapter, but did not give ISN like it does in boot mode. I found ISN in dump. Reading pflash failed

[crazylou2017]

Clone Xprog also great for HC05, I read many HC05 with 5.0 clone and always work.

What about Xprog 5.8.4?

[ghostrider72]

There is a bug in 4.85. Wont read EWS4 with adapter. Says chip not connected. But it works fine in 4.80

[p1et]

I have W203 EIS with HC08 8H62A mask MCU and I see something like this for the 1st time. This mask is not specified in vvdi software so can VVDI Prog read this under different mask 1J35D / 2J74Y ?

EDIT: I tried read as 1J35D and everything good.

[Weasel3]

I have W203 EIS with HC08 8H62A mask MCU. Can VVDI Prog read this under different mask 1J35D / 2J74Y ?

EDIT: I tried read as 1J35D and everything good.

So HC08 would work with 1J35D with W203
with W639 would be the same I guess?
ST12 W639 there is no option in the menu. So it is try and test between 5 options. Anyone have experience?

[p1et]

FOr W639 ST12 there is menu VITO(VIANO) ST12

[toutougsmserver]

I try read CEM range rover sport with mcu mc9s12xep768
And get partittion information error must choose manualy
When i choose manualy i can read dflash but eeprom is empty
Is this mcu has only dflash no eeprom or vvdiprog have problem with kind of mcu ?

[barho67]

try today to read 93lc66 from toyota rav4 immobox,reading 5 times and 5 times dump was bad,i try sixth time and dump was ok,for write the same 2-3 times not ok and 4th ok,with carprog read first time ok!

[figani]

try today to read 93lc66 from toyota rav4 immobox,reading 5 times and 5 times dump was bad,i try sixth time and dump was ok,for write the same 2-3 times not ok and 4th ok,with carprog read first time ok!

Bad with clip Adapter....?
Or bad reading by soldering...?

[barho67]

Bad with clip Adapter....?
Or bad reading by soldering...?

with clip adapter was not ok and after was ok,i didnt solder it.. its dip8 i think

[p1et]

If you read in socket then well, it is what it is, you might get different readings. If you solder then you 100% sure it's not bad connection issue, that's why I always solder.

[figani]

with clip adapter was not ok and after was ok,i didnt solder it.. its dip8 i think

solder down this black clip adapter and use Pomona. and you´ll see difference...
but in any case, with clip the chances to corrupt data are very high...

[barho67]

If you read in socket then well, it is what it is, you might get different readings. If you solder then you 100% sure it's not bad connection issue, that's why I always solder.

i solder 90% usually eeproms,but this one is 93lc66 in DIP8,so how can i solder it and where?)