FGTECH GALLETTO V54 FIX EPT HEX DUMP & PROGRAM FOR 0475 AND 0386

**gas43** · 2nd October, 2019, 07:27 PM

try to another laptop..

**Sarkan** · 5th October, 2019, 04:51 PM

On another laptop

**mcday** · 12th November, 2019, 10:51 PM

cerco firmware per galletto v50,
qualcuno può aiutarmi?
grazie

I am looking for firmware for galletto v50,
can someone help me?
thanks

**XJTAG** · 24th November, 2019, 02:57 AM

[QUOTE = joker01; 3521855] désolé les gars ...
quel fichier dois-je utiliser pour flash ????
d'après ce que j'ai compris ??? dtr qu'est-ce que c'est ??? [/ QUOTE]

the dtr is the pin of ftdi232 (only for control no used) you can use file with dtr or without dtr ,all files is same

**XJTAG** · 24th November, 2019, 03:31 AM

Originally Posted by reselie

Hi, i used ttl adapter to flash .hex. Then i forgot to disconnect from computer and when i used Mprog(or ftreadwrite - cant recall) i ended up with a TTL adapter that shows up as "FGTECH" on windows

you can restor ftdi232 eep

1 edit driver of fgtech and re-install your ftdi (add the vid/pid for ftdi usb rs232 converter in seting file of fgtech driver)
2 use Mprog and restor dump eep ftdi to ftdi usb rs232 converter
3 disconnect / connect from computer

**XJTAG** · 27th November, 2019, 12:08 PM

Originally Posted by gas43

successful upgrade v48 0475! Tested tricore vag med17.5 read/write.
But I have incorrect volt indication. at software 10.3 Volt but at the red cable 12.3 volt (multimeter tested). The error of voltage is in software.
older same case (post 1023) https://www.digital-kaos.co.uk/forum...letto-2/page69
I dont understand, Which resistor sould I change? near to D1? same pcb https://www.digital-kaos.co.uk/forum...4&d=1356199044
maybe, like this? https://www.addicore.com/82k-Ohm-1-4...-p/r6182ks.htm

hello gas43 please help me , if your interface V48 is same with my interface ?

i have old interface Europ v48 if i can upgrade it ?

**gas43** · 27th November, 2019, 03:10 PM

Originally Posted by XJTAG

hello gas43 please help me , if your interface V48 is same with my interface ?

i have old interface Europ v48 if i can upgrade it ?

Unfortunately no. Mine is like this https://www.digital-kaos.co.uk/forum...4&d=1356199044
As you can see, it has 11 legs for connections...

Dont spend your time with prehistorical tool which can damage your ecu...
Much better kess and k-tag.

**vnkto** · 10th March, 2020, 03:59 PM

Thanks bro ..

**MrTR** · 10th March, 2020, 10:06 PM

Hello guys - does anybody have FGtech software 2014 V54 or 2017 V54 - for V0475 ?

**MrTR** · 10th March, 2020, 10:15 PM

I connect LPC2119 on VD300 as in second picture - only RX an TX connection with programmer and wire jumper with ground on PCB.

Everything is ok and my VD300 is V475 now and working fine.

VD300 RX TX connection.jpg

**pena** · 28th March, 2020, 08:46 AM

The new china FG Tech 0475 working perfekt on Windows 10 64 bit, although they give it for Windows XP and Windowd 7 32/64 bit.

**PatricioPanama** · 24th June, 2020, 05:36 PM

Originally Posted by MrTR

I connect LPC2119 on VD300 as in second picture - only RX an TX connection with programmer and wire jumper with ground on PCB.

Everything is ok and my VD300 is V475 now and working fine.

VD300 RX TX connection.jpg

Thanks! I have the same V300. Now, with your picture and the files of fantomel, I have the mine working in windows 10 64 bits.

**Sarkan** · 21st July, 2020, 02:25 PM

FGTech Galletto, chinese copy.Does anyone know what this element is, marked with U2 in the picture.The device stopped working and I noticed that this part is very hot.Pin 1 is 0 volts and pin 3 is 3.3 volts.I removed the element and measured only 20 Ohms between pins 1 and 3.The device sometimes works, but I have to turn the USB cable on and off 30 or more times.If anyone knows please help me.