Everything Carprog...

**forumoto** · 9th December, 2015, 10:29 PM

hello buddy, finally my carprog works, can now pull pincode from CAN ecu..

I have one more issue and that is with EDC16 , Bosch EDC16C9,

what happens is that, after i read the ecu and display the pincode,

now when i click on Reset ECU,

the pincode does not changed to xxxx, it is still the pincode inside, even though i off the ecu for some time and reconnect and read , i still see pincode, please what can i do for EDC16 ecu's in other to get the pincode reset. thank you

**prahlad14** · 14th December, 2015, 01:20 PM

thanks will try to test

**eudes** · 17th December, 2015, 09:39 PM

muito obrigado

**Catdaddyfunk** · 23rd December, 2015, 05:34 AM

Originally Posted by eudes

muito obrigado

???????????

**marco242** · 30th December, 2015, 08:46 PM

Could someone help me with schematic diagram of wires (pin A1 to DB25) from A1 adapter to carprog, I changed everything in A1 adapter, but it does not work on CAN.

**marco242** · 30th December, 2015, 09:02 PM

delete post #51

**FxShaw** · 17th January, 2016, 04:47 PM

When doing Nissan module on bench with infineon...and getting these codes
B0F8E unknown B058F/B058D Unknown... This is what they really mean..

Nissan B0F8E Side Collision // B058F/B058D Crash Data
B1416 Control Unit Bad ---Not good code to have :-). mostly caused by wrong clear.
B0591 - Rear Collision

Edit..They Finally listen and add the description in CP..Don't need this anymore. I will update the list if I find more unknown codes and try to make it more accurate.

**UTAuto** · 7th February, 2016, 04:50 AM

Hey guys, I have the v07.28 version from china (clone) I'm trying to clear crash on Ford Fiesta with Infineon XC2361. This version said that I need to activate this feature "Ford 2009+ airbag sensors with MAC and Infineon processors programming by OBDII". Is there a way to get this for this clone version. I have the A1 and C1 adapters but the software is not there.
Any idea. Thanks

**Catdaddyfunk** · 8th February, 2016, 03:28 AM

Not possible with clone unless it's the russian clone version supposedly..

**Frankcar** · 8th February, 2016, 05:31 AM

i have carprog original and tried for clear a srs unit 89170-60350 Toyota LC200 but not working clear dump.
c66 eeprom

**Frankcar** · 8th February, 2016, 05:40 AM

with carprog original you can't read/write data MAC and Inifineon via BDM . only CAN or OBD
via CAN or OBD reading 99% good but for write have problem for some units
for reading via CAN ( you need 4 pin sure from unit: Ground , power 12v , CANH , CANL + Resistor )

**Air** · 13th February, 2016, 03:35 AM

Originally Posted by Frankcar

with carprog original you can't read/write data MAC and Inifineon via BDM . only CAN or OBD via CAN or OBD reading 99% good but for write have problem for some units for reading via CAN ( you need 4 pin sure from unit: Ground , power 12v , CANH , CANL + Resistor )

Use updated A1 MULTY adaptor. Today I've tried to communicate by regular A1 adaptor with SRS module on board. It have been the 2015 KIA Sorento with 95910-1U180 (Infineon) NO LUCK. But with A1 MULTI I was able to read this module at least. Tomorrow I need to find a solution to clear crash data then I'll try to write back clear dump

**Domi** · 24th February, 2016, 07:00 PM

You want to build a10 adapter for Clone why must trim pin 22 or not ?

Attachment 360011

**FxShaw** · 24th February, 2016, 10:30 PM

Originally Posted by Domi

You want to build a10 adapter for Clone why must trim pin 22 or not ?

Attachment 360011

Not..Use the exact schematics

**Frankcar** · 26th February, 2016, 05:29 PM

Please help me for adapter A10
I hava original package full airbag with this adapter
I think this adapter have problem,if anyone have this adapter please take a photo and send me
Support carprog told me this adapter clone , now distributor no answer to me
Thanks