VVDI 2 new tool arrived

**momogsm** · 10th January, 2021, 06:37 PM

Originally Posted by offsystem

not keyless System

but how to fix this?

Gesendet von meinem SM-G986B mit Tapatalk

Hi

You Can Force Ignition By Make A Bridge In The Keyless Entry Module Connector That Is To Be Found Under The Plastic Cover Right Below The Steering Wheel,

Post A Picture Of The Plug, To Identify Which Version,

Regards

**Jimmy07** · 11th January, 2021, 12:28 AM

A blown 5 amp fuse can cause screen to go black

**cristo_844** · 11th January, 2021, 12:44 AM

Originally Posted by offsystem

not keyless System

but how to fix this?

Gesendet von meinem SM-G986B mit Tapatalk

Try disconnect the car battery and reconnect again after a few minutes!

**PerryZhang** · 11th January, 2021, 04:09 AM

Originally Posted by dimet

How to use this option?

you need activate that license first ,then buy one id48 collector , and also in the software it will guide you step by step

**sniegavirs** · 11th January, 2021, 10:02 AM

Does anyone have any info where and when will be available to buy Xhorse XM proximity remote keys?

**PerryZhang** · 11th January, 2021, 12:36 PM

still not yet ,it will start sell in china and test it ,

**nikovali** · 11th January, 2021, 10:56 PM

Seat Alhambra /2007 AKL

I tried to read the pin with vvdi2, I have read the pin and sc from ECU. With the pin I try to learn new key, vvdi2 reported that the key is learned but the car is not starting, after that I try to add new key with vcds but vcds reprted that the pin is not correct. Any help is much appreciated!

**ghostrider72** · 11th January, 2021, 11:16 PM

Did you precoded it first?

**Weasel3** · 11th January, 2021, 11:22 PM

Originally Posted by nikovali

Seat Alhambra /2007 AKL

I tried to read the pin with vvdi2, I have read the pin and sc from ECU. With the pin I try to learn new key, vvdi2 reported that the key is learned but the car is not starting, after that I try to add new key with vcds but vcds reprted that the pin is not correct. Any help is much appreciated!

Partnumber Cluster?

**jokir** · 12th January, 2021, 06:38 PM

I assume the dash is a visteon
Connect a dump from the ECU and a new scb from the dash

**nikovali** · 12th January, 2021, 10:43 PM

Originally Posted by Weasel3

Partnumber Cluster?

7M7920840Q VDO V46
ECU-EDC15xx

**Weasel3** · 12th January, 2021, 11:56 PM

You make TP22 first ?
And only use PIN ?

Sure you read the exactly right number on the engine ECU ?
Try to read Km at the same time. And compare with what cluster says.

It might need precoding with 7bytes, you only get 6 out of the engine ECU.
So the last pair could be a hazzle to sort out.

Could it be more a Ford part this one. Not the usual look of a VAG cluster.

**nikovali** · 13th January, 2021, 12:09 AM

VVDI2 read ECU EDC15xx
PIN 01134,CS:57 62 D5 9F 67 41 A5

**mikajna** · 13th January, 2021, 12:20 AM

Originally Posted by nikovali

VVDI2 read ECU EDC15xx
PIN 01134,CS:57 62 D5 9F 67 41 A5

Alhambra is like Sharan, it should be transponder pcf7935 prepared as VW ID44.

Good luck

Послато са SM-A505FN помоћу Тапатока

**Weasel3** · 13th January, 2021, 10:39 AM

This is what the list says:
SEAT ALHAMBRA 2000-2003 PHILIPS Crypto ID44 PCF7935AS (VAG precoded)
SEAT ALHAMBRA 2003-2006 Crypto 48 ID48
SEAT ALHAMBRA 2006-2010 MEGAMOS Crypto-SEAT precoded TP22

Check you VIN production date of the vehicle.

You must test in VCDS if key is accepted - mod25,mea_block08, then chose block_001. This will tell you if key is accepted, to be programmed.
With ordinary TP22 or precoded as well.

And off course PIN needs to be accepted.
And also check lock time. If so, might need to stay with ignition ON. Connected to a charger quite a long time. To count down the minutes. This is visible in VCDS.