Can-Am Bike immo

[arlalex1]

Hi Fiends

How to do key programme for this can-am bike immo?

ther is a eeprom 2931A and PCF7991AT and MCHC90B

Original key is Temic 12 (ID12)

Please helo

[gepakg]

what is this can-am spyder?

you can easy copy temic 12 to an T5...as i see on picture you have original key...

2931 is not eprom,this motorola hc908 is very hard to read and based on external immo for old aprillia bikes (rsv4,etc.) and ecu siemens-VDO...

regards Gepa

Hi Fiends

How to do key programme for this can-am bike immo?

ther is a eeprom 2931A and PCF7991AT and MCHC90B

Original key is Temic 12 (ID12)

Please helo

[arlalex1]

Hi

Thanks for your reply.

Yes this is spyder and all the keys lots. This key customer bring it from dealer.
please advise me how to make the key programme.

Regards
Alex

[gepakg]

key that you get from dealer can be programmed only with BRP orginal diagnostic tool because can-am spyder is family of bombardier (BRP) or to try with abritus that can emulate diagnostic protocol J2534 with BRP orginal sw (B.U.D.S.)

if you read with success hc908qt_qy inside immo i can help you to generate logic for an temic 12 write to T5 and start this bike with 3 wheels :-)

regards Gepa

Hi

Thanks for your reply.

Yes this is spyder and all the keys lots. This key customer bring it from dealer.
please advise me how to make the key programme.

Regards
Alex

[ray-ray]

Gepakg Good to have you here your knowledge is away spot on. I pick up so much info. from your post. Thanks!

[lupu_sandu]

As far as i know you can disable KESS with BUDS without a problem.

[gepakg]

yes,exsist this option in B.U.D.S. but for BRP sea-doo...never tried with spyder,have in workshop siemens-VDO ecu with disabled KESS open it and tried to read st10f269-t3 but always without success,lift all pins,everything tried also on few ecu`s from ski-doo,sea-doo,can am quad etc,always without success :-(

on spyder is story bit different,have external immo and temic 12 used in key,for sea-doo,ski-doo dallas inside small simple key

BTW. somebody successful read st10f269 from this ecu`s?

regards Gepa

As far as i know you can disable KESS with BUDS without a problem.

[phuongnt]

Hello gepakg,

Could you please show me the location of HC908 on the DESS module? I will try to read it and send to you for help generate T12 keys for the all-lost-key spyder.

Many thanks
s-l1600 (3).jpg

key that you get from dealer can be programmed only with BRP orginal diagnostic tool because can-am spyder is family of bombardier (BRP) or to try with abritus that can emulate diagnostic protocol J2534 with BRP orginal sw (B.U.D.S.)

if you read with success hc908qt_qy inside immo i can help you to generate logic for an temic 12 write to T5 and start this bike with 3 wheels :-)

regards Gepa

[phuongnt]

@gepakg: never mind, I already saw the photo from arlalex1.

[motobrothers]

I have brp original diagnostic tool. You must have a working key to program another. The procedure appiles only spyder. For ATV, Sea doo etc. do not meed working key, we can add a normal key or performance key.

[chaveirotere]

Alguém poderia ler o hc908, estou com um spyder brp no workshop e quero tentar ler, tenho upa-se e vvdi prog
Someone could read the hc908, I'm with a brp spyder in the workshop and I want to try to read, I have upa-s and vvdi prog

[adelnooh]

if i read hc908 in immo
how can i add T5 transponder in it?

[avibatman]

can am spyder 2002 - 2012 all key lost, you can´t make keys usign the BUDS software you have to change the DESS module and add new keys, spyder 2013-2022 you can add an all key lost whit BUDS software. if some one can read and brick the security of the MCU i have one to tryWhatsApp Image 2022-01-25 at 1.11.55 PM.jpg

[moto yong]

Hello, how to read this chip, is the chip encrypted?

[koched]

Any solution?