***** SMELECOM SUPPORT THREAD *****

[teerak2uk]

Anyone else had a similar problem had it on a Audi A7, A3 2012

[antibisic]

check your obd plug

[teerak2uk]

check your obd plug

Did the test from the machine and seems ok

[levisdj]

w205 07.14 big display.... anyone tried??

[esx503]

Anyone else had a similar problem had it on a Audi A7, A3 2012

I usually get that message when I selected the wrong program or the car isn't compatible.

Sent from my SM-N950U using Tapatalk

[esx503]

what seem to have gone wrong here? it gave 7 digits also tried different volts still no go

The calculation is wrong. Try a different calculator. Or try doing it with a different machine. When it displays more numbers than what it's supposed to I do t even mess with I try to find the program that will do it correctly

Sent from my SM-N950U using Tapatalk

[teerak2uk]

I usually get that message when I selected the wrong program or the car isn't compatible.

Sent from my SM-N950U using Tapatalk

Audi A7 only has one option and it did it a couple of times in the past but after disconnecting plugs/cables and trying again was ok but strange thing is when you do tests it seems to pass ok

[optimistic]

hi anyone done 2014 hyundai elantra mb91f06bs? i have 3 options on menu not sure which to use if so can you please help me thanks

[javyb]

hi anyone done 2014 hyundai elantra mb91f06bs? i have 3 options on menu not sure which to use if so can you please help me thanks

Best to remove cluster and read the micro mask then proceed. If u select the wrong option you will damage the dash

Sent from my SM-N960F using Tapatalk

[morrisgauge]

Hello friends. I was playing around and plugged in my DSP3 via OBD on a USA version 2001 VW Beetle TDI. Smelecom has only OBD options listed for it on my DSP3. Anyways, I clicked "Read KM" and an incorrect value came up. I backed out of the menu, because I wasn't even programming this car, BUT the odometer displayed the read value (3447). I hadn't programmed it, yet the odom value changed?! Very strange. It starts and all instrument cluster functions are fine. I drove it a few miles, the trip and odometer cycle fine. Has anyone run into this before? I don't do too many VAG vehicles, but I know I've done a few Audi's with my DSP3, plug and play, no problem. I appreciate any info, thanks.

[DUSTYDUSTER]

Hello my friends ,
for my first use of DSP3 the device require a code pin , whre can i find this code please ? i have somthing other strange : the touch screen dont allow me to write any digit with or without the pen , is this normal on DSP 3 ?
Thank you for your help

[esx503]

Hello my friends ,
for my first use of DSP3 the device require a code pin , whre can i find this code please ? i have somthing other strange : the touch screen dont allow me to write any digit with or without the pen , is this normal on DSP 3 ?
Thank you for your help

I think it's the last 5 digits of your serial number. something like that either last 4 5 or 6 I don't remember exactly. you should be able to write it with anything with no issue try to bring up the keyboard by hitting the lower right corner where it says large in display I think that's what it say see if that works. post a pic of your device

Sent from my SM-N950U using Tapatalk

[mohdmalik90]

i have dsp3-usaprog, anyone knows which adapter i can use for obd but not on the car, on the bench on the cluster plug, and if there is any color code availaible, for power , ground and CAN lines for smelecom adapter. it didnt come with much instructions. do i have to make my own obd connector? thanks

[evss]

just checked the site looks like you will have to make one

[XmoDDeR]

new adapter denso for smelecom avail liske stool conection