X-Prog M

[bram380]

Can you post here software for update? And if you xprogm is ~~~~ed up after update, exist some good atmega64 dump?

I use software from t*t.lt
Update time less than 2 minuts.

click below:
xprog-m version 5.0 (2010-04-26)

pass: digitalkaos

[obdmaster]

Now my XPROG-m clone with 21 authorization.




See xprog-m clone full authorization:
wooow... see this video...

Bram why do you think this update was succesfull where other members have failed m8?

My xprog-m has no micronas authorisation do you think i might gain that or lose everything.
Its a tightrope m8

[branco]

I have clone from ecutool
I updated sucssefully
this version don't erase authorizations
I am very happy
I got now "originel" clone
regards

[obdmaster]

I have clone from ecutool
I updated sucssefully
this version don't erase authorizations
I am very happy
I got now "originel" clone
regards

My clone is also from ecutool, bought before full authorisations on clone was available.

Really not sure if i should give it a go?

like i said before its a tightrope

[bram380]

i got xprog-m clone from Clone Ltd.

[teerak2uk]

I`m too scared you first obdmaster

[blackpirate]

donno what to say guys....
never used a programmer!

maybe its a "bug" into the software!
looks like they forgot to add the protection.....

my opinion its that will be fixed soon!
you realize that they loose lots of $ !

cheers

P.S:
i am not encourage to update your programmers!
do it on your own risk!

[obdmaster]

I`m too scared you first obdmaster

Still contemplating wether to try it or not m8


Just seems a bit toooooo goooooooooood at moment.

I am always the pessimist m8.


Just glad my xprog is at work, otherwise id be dooin it right now.

with it being at work gives me time to think.

I bet lupu sandu is doin it right now m8

[teerak2uk]

mine is right here in my right hand (xprog that is) and im tempted Hmm do i dont i do i dont i

half tempted cos the issues i`ve had recently with srs modules so mine might even have faults as it is

[bram380]

Any risk of damage and loss of authorization is not my responsibility.

Previously I contact the seller, if xprog-m clone defective because it used new software, they were able to fix it.

Unfortunately I have not had time to record the video while the software update, because it was so stressful ....

[obdmaster]

mine is right here in my right hand (xprog that is) and im tempted Hmm do i dont i do i dont i

half tempted cos the issues i`ve had recently with srs modules so mine might even have faults as it is

Im also very tempted as i have no micronas authorisation, and could do with that. hhmmmmmmmmmmmmmmmmmm.
What shall we do teerak2uk, put it down you filthy git.

[teerak2uk]

Any risk of damage and loss of authorization is not my responsibility.

Previously I contact the seller, if xprog-m clone defective because it used new software, they were able to fix it.

Unfortunately I have not had time to record the video while the software update, because it was so stressful ....

so did you just install the new software or did you click the update tab?


many thanks

[bram380]

so did you just install the new software or did you click the update tab?


many thanks

after install new software v5.0, this xprog-m clone undetect, so all authorization blank.

then i update with stressfull...
and.... less then 2 minuts update was sucessfull.

[branco]

I recoomand to update just now before they fix the "bug"
mine is fully working now
regards

[teerak2uk]

here we go then