Programming key Renault!

[Catalizator]

pin megane 2

[T2000]

Hello,
Thank you Catalizator.
I was still not successfull :/

The FVDI software is not running with Renault. It crashes when loading

What is another good solution?
I tried so many times.
I would also go and find another locksmith in Berlin who can help.

Suggestions very welcome!!!

[Catalizator]

hi.renault ecu tool, renolink, x100....
and many instruments write keys. depends on the price that suits you

[tomalamix]

hy guys and sorry to dig this thread up,

I've bought the FNR to code keycards to Renaults until 2008 but is going to take a while to arrive so I also have a copy of DDT4ALL / DDT2000 around here and the proper cable to work with it, but i dont use it for a long time.

Is it possible to programm keycards using the DDT4ALL or/ DDT2000? I saw around here some threads that it can be done but the procedure is not very clear.

Does any one have experience with this particular procedure?

Ive found this procedure so far:

1.first you make read UCH
2.ignition switch off
3.enter APV code
4.press buton start APV
5.insert new key and turn ignition on
6.after led immo off wait 5s. and turn ignition off
7.insert next key and turn ignition on
8.after led immo off wait 5s. and turn ignition off
9. press Valider button and afterwards Abandon Mode APV
10. now test new key and remote.

I have doubts about this since there is no ignition off or on procedure if the card isnt recognized in megane 2, the ignition will only go ON if the card is already coded to the car. Can anyone confirm or correct this procedure?

Thanks

[tomalamix]

Hello again,

I've been testing and found that I can't read properly the ISK for an Megane 2 PH I (its a 2004 car, im sure its Phase I) ..strange...Am I doing something wrong?

Please check the printscreen and post your comments pls, i would appreciate some help. thank you!

[tomalamix]

Here i send the response to the request on address 21AB from the UCH:





The supposed ISK is being read correctly so i'm really in the dark here

[Christiano76]

Hello, if you go to this table, you can normally assign the cards after retrieving the PIN code
I made a translation of the procedure for assigning badges.procedure carte ddt4all.JPG

read the PIN code without putting the badge in the reader.

.DDT4ALL UCH Mégane II.JPG

[tomalamix]

Hy Chris,

yes, you're right but this time, i don't know why I can't get a proper PIN code from the ISK that ?m reading, I'm very confused...

BR

[Christiano76]

Test with Renolink 1.49 if you have an original OBDlink SX probe which you can have here:

https://mega.nz/file/1gQlhaJb#T_CkV4...L1kiyHYyxohQbw

[Christiano76]

Do you have this function on your DDT4ALL?
If you don't have this extension, here is a link and you install the ddtplugins file in: C:\Python27\Scripts\ddt4all-master
https://mega.nz/folder/0wAxgaYY#Yhrbcf3_b24O86x4MT2E0Q

ddt4all extesions.JPG

[tomalamix]

Do you have this function on your DDT4ALL?
If you don't have this extension, here is a link and you install the ddtplugins file in: C:\Python27\Scripts\ddt4all-master
https://mega.nz/folder/0wAxgaYY#Yhrbcf3_b24O86x4MT2E0Q

ddt4all extesions.JPG

I think i do, check my post #20. The window that should show is that one, right? Your DDT is in French, right?

BR

[tomalamix]

Test with Renolink 1.49 if you have an original OBDlink SX probe which you can have here:

https://mega.nz/file/1gQlhaJb#T_CkV4...L1kiyHYyxohQbw

I don't have that cable and for this particular case this should be all very straight forward and so far it's not...

[Christiano76]

yes, it's this window and my ddt4all is in French

[tomalamix]

yes, it's this window and my ddt4all is in French

Hy Chris

I thought so, and thank you for your inputs on this. So since I'm using every right tools and plugins i don't understand why is this happening. Someone else could give some hints pls?

thanks

[Christiano76]

look at post #22